User manual TEFAL PREMIO

[. . . ] T. M. , PostScript T. M. , Adobe Systems Inc. ; Macintosh EtherTalk, LocalTalk, TrueType Reg. , Apple Computer Inc. ; Novell, NetWare, Unix, YES NetWare Tested and Approved logo, Reg. TokenRing, T. M. , International Business Machines Corp. ii TEFAL OkiLAN 6100e+ User's Guide Organization and Contents Organization This manual has been divided into eight sections. Section I contains and installation instructions for the OkiLAN 6100e+ print server. [. . . ] The gateway address must follow the format XXX. XXX. XXX. XXX, where each XXX is a number between 0 and 255. When the default gateway is changed, it will remain undetected until the OkiLAN 6100e+ is reset or is power cycled. Note: If you select an invalid default gateway or the default gateway goes down, the OkiLAN 6100e+ may not be able to communicate with non-local networks. Configure Port (Option 6) After the Configure menu appears, you can access the following configuration option screens. Specify Configuration Page Language This option enables you to select how the OkiLAN 6100e+ configuration pages should be printed: Text (default), PCL, PostScript, or OFF. Configure Language Switching TCP/IP This option asks you to select the language of your printer. For a description of language switching options, see pages IV-28 and IV-29. Configure Printer Type This option enables you to indicate the printer type to which the OkiLAN 6100e+ is connected. Custom printer. TEFAL OkiLAN 6100e+ User's Guide IV - 45 Section 4 - Chapter 5 - Telnet Configuration · Language Switching Sequence - If you select Custom Printer from the Configure Printer Type screen, you must indicate the switching sequence to be used for both PCL and PostScript. This is only necessary if language switching is set to something other than OFF. TCP Connection Configuration (Option 7) TCP Connection Timeout This is used to sever network TCP/IP Connections that are idle for more than a specified period of time (between 1 and 3600 seconds). Under most conditions you will want to leave this function enabled. Raw Port Number Set the port number where the raw port connections will be accepted. Download New Firmware (Option 8) This option is provided for future product modifications and enhancements. CAUTION: Do NOT use this option without having the upgrade files on hand. The latest firmware and utilities are available through: · World Wide Web: http://www. okidata. com Firmware update instructions are available with the download file. IV - 46 TEFAL OkiLAN 6100e+ User's Guide Section 4 - Chapter 5 - Telnet Configuration Restore to Factory Default Configuration (Option 9) This option automatically restores the OkiLAN 6100e+ to its original factory defaults. Be aware that when you restore the OkiLAN 6100e+ to the original factory default settings, only the TCP/IP protocol and output port information is restored and your TCP/IP password and IP address are erased. CAUTION: Make sure that no print jobs are active when you select Restore to Factory Defaults. Example: Sep 6 14:38:43 bootpd[17565]: hardware address not found: 004068175042 This message appears when the BOOTP server received a request from a device not in its internal bootptab tables. IV - 50 TEFAL OkiLAN 6100e+ User's Guide Section 4 - Appendix A - Troubleshooting Static Route Entry If the OkiLAN 6100e+ has printed a configuration page showing the default address, but it cannot be reached through telnet, check the following: · Display the host's routing tables with the `netstat r' command. · Verify the OkiLAN 6100e+ is on the same subnet as the host from which you are telneting. As a drastic measure, try creating an isolated subnet with your host and the OkiLAN 6100e+. If you are using 10BASE2, run the cable directly from the host to the OkiLAN 6100e+. If using 10BASE-T cabling, connect the host to the OkiLAN 6100e+ through a hub not connected to any other host. · If the static route has been set up and can telnet to the OkiLAN 6100e+, but your changes do not seem to be saved, check the host's routing tables. You might have telneted to a different OkiLAN 6100e+ than the one you intended. While in telnet, select the second menu option, Show Network/Printer Information. · If you are able to ping to the OkiLAN 6100e+, but are unable to telnet, the IP address is probably being shared with another device that does not support telnet. TEFAL OkiLAN 6100e+ User's Guide IV - 51 TCP/IP Section 4 - Appendix A - Troubleshooting OkiNet for TCP/IP - Winsock Errors · If you see an error before OkiNet for TCP/IP appears on the screen, try setting a host name in the hosts file in the Windows directory (check the documentation for your Windows TCP/IP stack). · If you have difficulty seeing a particular OkiLAN 6100e+, try moving the device onto the same subnet as the computer running the utility. · If OkiNet for TCP/IP gives you the Winsock error: Could not bind to socket, use the Special Options dialog under the File menu to change the Discovery UDP Port to a different port number. Hardware Error Messages ST: Cable not connected Self-test has determined that the network cable is not connected. [. . . ] There is no guaranteed that interference will not occur in a particular installation. If you suspect that this equipment is interfering with radio/TV reception try the following: · While observing the interference, turn the suspect equipment off and back on. If the inteference stops when you turn the equipment off , and starts again when you turn the equipment on, the equipment is probably the source of your problem. · Connect the equipment and the receiver to different electrical outlets. [. . . ]