User manual TECHWOOD STR84

[. . . ] STR-84 260 WATT STEREO RECEIVER OWNER'S MANUAL CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance. WARNING: TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE. IMPORTANT SAFETY INSTRUCTIONS CAUTION: · Read all of these instructions. · Follow all warnings and instructions marked on the audio equipment. [. . . ] MEMORY button Use to store FM/AM stations in memory (See page 17). 17. MODE button Use to select the Normal Tuning Scan or Preset Channel scan modes. FM MODE button When activated, this unit automatically switches into the stereo mode when a stereo broadcast is received and the stereo light illuminates. The stereo indicator will not illuminate in the mono mode. 9 Display 1. Input source, frequency and level indicator Function display : When you press input selection button, the selected input source will be shown. Frequency display : When you select Tuner input source, FM/AM frequency will be displayed. Surround Sound Level display : When you adjust the level of center, rear and delay when operating unit in surround mode, the level will be displayed in dB. 4. TAPE Monitor indicator This indicator will illuminate When you press TAPE MONITOR button. 5. STEREO indicator This indicator will illuminate when FM stereo broadcasting is received. TUNED indicator This indicator will illuminate when a radio station is precisely tuned. 2. Memory Channel indicator The number of the memory channel which is selected will be displayed. 7. TIMER indicator This indicator will illuminate when the timer is used. 3. MEMORY indicator Press the MEMORY button and the MEMO indicatorwill light. If you press the MEMORY button and release instantly, the indicator will blink 4 times. If you press the MEMORY button longer than 1/2 second, the indicator will remain lit until the automatic programming is completed. 10 REMOTE CONTROL UNIT Using the Remote Control Unit By using the provided remote control unit, the receiver and matched optional components CDC-85 and TDX-85 can be controlled from your listening position. To use the remote control unit, point it at the REMOTE SENSOR window of the receiver. Battery Installation REMOTE SENSOR window of the receiver 1. Make sure that the batteries are inserted with their positive and negative poles positioned correctly. Close the cover until it clicks. Battery Replacement If the distance required between the remote control unit and main unit decreases, the batteries are exhausted. In this case replace the batteries with new ones. Notes : Even if the remote control unit is operated within the effective range, remote control operation may be impossible if there are any obstacles between the unit and the remote control. If the remote control unit is operated near other appliances which generate infrared rays, or if other remote control devices using infrared rays are used near the unit, the stereo may operate incorrectly. Converseiy, the other appliances may also operate incorrectly. Precautions concerning batteries Be sure to insert the batteries with correct positive " "and negative " " polarities. When the remote control unit is not to be used for a long time (more than a month), remove the batteries from the remote control unit to prevent them from leaking. [. . . ] The picture from the video souce can be seen on the TV and the sound from the video source will be heard from the speakers, provided both are properly connected to the STR-84 as shown on page 5. Video Editing Function This feature lets you replace the sound from a VCR with sound from an AUDIO source such as CD during video signal dubbing. Press the DVD/VIDEO 3 (or VIDEO 2) button and operate DVD/VIDEO 3 (or VIDEO 2) for playback. Select the audio source with the source selector buttons, and then operate the selected audio component for playback. Now you can watch the picture from the video component on the TV, and listen to the sound from the audio component through the speakers. [. . . ]