User manual TECHWOOD DVR99

[. . . ] DVR99 HOME THEATER SYSTEM This "QUICK-START GUIDE" will get you started without reading the complete owner's manual. However, we recommend you take time to read the owner's manual completely to learn about all of the features and operating instructions for the DVR99. The Quick Guide covers only basic connections and operating instructions. The owner's manual includes important safety information and describes in detail, the advanced features and operating instructions of the DVR99. RISK OF ELECTRIC SHOCK DO NOT OPEN QUICK-START GUIDE PL EA S CAUTION ER EA D! CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). [. . . ] Connect the surround speakers' wires to the receiver's SPEAKERS REAR L and R terminals. Connect the center speaker's wire to the receiver's SPEAKERS CENTER terminal. Plug the AC power cord into an AC wall socket. INSTALLING BATTERIES IN THE REMOTE CONTROL Your remote control requires two AAA batteries (supplied) for power. For the best performance and longest life, we recommend alkaline batteries. C autions: · Use only fresh batteries of the required size and recommended type. · Do not mix old and new batteries or different types of batteries. Slide the battery compartment cover in the direction of the arrow to remove it. Place the batteries in the compartment as indicated by the polarity symbols (+ and ­) marked inside. When the remote control stops operating properly, replace the batteries. C aution: If you do not plan to use the remote control for a month or longer, remove the batteries. Batteries can leak chemicals that can destroy electronic parts. 9 RECEIVER OPERATION A QUICK LOOK AT THE RECEIVER'S CONTROLS T UNING MODE In tuner mode, pres s to s witc h between pres et and manual tuning (s ee " S witc hing B etween P res et S tations and Manual T uning" on P age 11). DIMME R ­ P res s onc e to dim the dis play panel. P res s again to return it to normal. DT S ­ P res s to s witc h to 5. 1 C hannel DT S from s tereo mode. S UR R OUND MODE P res s to s witc h s urround modes between P R O L OG IC , T HE A T E R , HA L L , and S T A DIUM for analog equipment. DOL B Y DIG ITA L ­ P res s to s witc h to 5. 1 C hannel Dolby Digital from s tereo mode. Note: Y ou c annot us e thes e buttons in tuner mode. F UNC T ION ­ R otate to s elec t the S TE R E O ­ P res s to s witc h from s urround mode to s tereo mode. T he s elec ted s ourc e name appears on the dis play panel. V OL UME -- R otate to s et the des ired volume. Dis play P anel P HONE S ­ T his T ONE -P res s to turn tone on and off and to adjus t bas s and treble. (s ee page 12 HOW T O A DJ US T T ONE ). ME MOR Y / DIS C 3 P L A Y B A ND/ DIS C 1 P L A Y -s tores a s tation in memory in tuner mode. -P res s to playbac k dis c 3 in DV D/C D mode. S T OP -IN DV D/C D mode, pres s twic e to s top the dis c . -P res s to s elec t A M or F M band in tuner mode. -P res s to playbac k dis c 1 in DV D/C D mode. jac k is c ompatible with many c onventional dynamic NIG HT MODE headphone types . ­ W hen the When you c onnec t s ound s ourc e is headphones , the Dolby Digital unit automatic ally pres s to c oms elec ts s tereo pres s the dymode. (s ee " Us ing Night Mode" on P age 12). T UNING /P R E S E T ­ R epeatedly pres s to tune to A M or F M s tations and s elec t pres et s tations in tuner P A US E mode. (S K IP +/-, S C A N +/-) ­ Us e to adjus t bas s and treble -P aus es the dis c in DV D/C D mode. F M MODE / DIS C 2 P L A Y -In tuner mode, pres s to s elec t s tereo or monaural mode for F M. -P res s to playbac k dis c 2 in DV D/C D mode. 10 USING THE TUNER 1. [. . . ] After checking, if needed, reconnect. Power line of a fluorescent light is installed near this product. Source being played is not recorded or broadcast in surround sound or stereo. One or more rear speaker wires is not making good contact, Place this product as far away as possible from electric devices with interference. After turning off the power and then turning it on again, reduce the volume or change to the correct 6-ohm or higher speakers. [. . . ]