User manual TECHWOOD DVR100

[. . . ] DVR100 READ THIS FIRST This audio system is made and tested to meet exacting safety standards. W AR N I N G : To reduce the risk of fire or shock hazard, do not expose this product to rain or moisture. C A UT ION R IS K OF E LE C T R IC S HOC K . DO NOT OP E N. be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: · Reorient or relocate the receiving antenna. · Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. [. . . ] Use the on screen display on your TV and use the buttons on the remote to navigate to the desired folder and song title and then press play. Note:: When the DVR100 finishes playing an audio CD, it automatically plays the disc in the next drawer until the disc in drawer 3 is finished. Playback will then stop. Changing the Sound Mode For an analog source(Tuner, SAT, TV, Tape, CD or AUX). repeatedly press SURROUND MODE until the desired mode (THEATER, HALL, STADIUM, PRO LOGIC, PRO LOGIC movie, or PRO LOGIC music ) appears. Or, repeatedly press SURROUND on the remote until the desired mode appears. To set the bass and treble levels to 0dB press the tone button on the receiver or on the remote until TONE OFF appears in the Note: If your DVD is encoded for 5. 1 Dolby Digital sound, pressing display. If the DVD is encoded for anything less than 5. 1 Dolby Digital sound, the DVD plays in Dolby ProLogic mode and pressing SURROUND changes Dolby ProLogic to Dolby digital Stereo. 12 REMOTE CONTROL OPERATION A QUICK LOOK AT THE REMOTE CONTROL TEST TONE -- Turns on or off the test tone function in DTS, DOLBY DIGITAL, or PRO LOGIC mode. The test tone is output from Front L speaker, Center speaker, Front R speaker, Surround R speaker, Surround L speaker, (optional subwoofer speaker when subwoofer is on). SPEAKER CONFIG/LEVEL/DELAY-- Use to change speaker settings and adjust level and delay. VOLUME -- Use to adjust volume. FUNCTIONS -- Use to select the desired function. TUNING MODE -- Switches from tuning to preset mode. SURROUND -- Repeatedly press to change the surround mode to PRO LOGIC, PRO LOGIC II MOVIE, PRO LOGIC II MUSIC, THEATER, HALL, STADIUM or STEREO. PRESET ­ When in tuner mode, use + or to change frequency one step at a time or to select preset stations. When in DVD/CD mode, use to select tracks. TONE -- Press to use tone on, bass adjust, treble adjust or tone off. Use or when adjusting BASS and TREBLE. BAND / MEMORY/ -- Press to memorize the desired station frequency. This button also begins playback of Disc3 when in DVD/CD mode. -- Selects AM or FM band while in tuner mode. This button also begins playback of Disc2 when in DVD/CD mode. LEVEL AND NAVIGATION -- Use to make menu selections and to adjust levels. FM MODE / DVD FUNCTIONS -- MUTE -- Press to turn off the sound level. To restore the sound, press again. SLEEP -- Press to set the sleep time. Important: If you change functions using the function knob on the front of the receiver, you must also press the corresponding function button on the remote control to operate the unit with the remote control. OPERATING RANGE OF THE REMOTE CONTROL The remote control may not work properly if: · There are obstacles between the remote control and the receiver's remote sensor. · Direct sunlight or fluorescent light is shining onto the remote sensor. · The receiver is located near a device that is emitting infrared rays. · The receiver is operated simultaneously with another infrared remote control. 13 SETTING UP THE SURROUND SOUND SYSTEM If you purchased the DVR100 with mini or bookshelf speakers and a powered subwoofer, you do not have to set the speaker sizes. The DVR100 comes from the factory pre-set for use with small front, center and rear speakers and a powered subwoofer. If you purchased the DVR100 with large floor standing speakers or change your speakers at a later date, you must set speaker sizes using the SPEAKER CONFIG function on the remote control as described below. You can also adjust the channel output levels and speaker distances as described below. 3. To change the center speaker's level, repeatedly press or until you reach the desired level ( -10 to +10dB ). To change the front right speaker's level, repeatedly press or until you reach the desired level ( -10 to +10dB ). To change the rear right speaker's level, repeatedly press or until you reach the desired level ( -10 to +10dB ). [. . . ] reduce the volume or change to the correct 6-ohm is no sound even or higher speakers. Set Surround Mode toDTS, DOLBY DIGITAL, DOLBY PRO LOGIC, DOLBY PRO LOGIC II No sound from the rear Surround Mode is set toSTEREO. Source being played is not recorded or broadcast in surround sound or stereo. One or more rear speaker wires is not making good contact, No sound from the center speaker. [. . . ]