User manual TECHWOOD CDC85

[. . . ] CDC-85 COMPACT DISC CHANGER OWNER'S MANUAL CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance. WARNING: TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE. IMPORTANT SAFETY INSTRUCTIONS CAUTION: · Read all of these instructions. · Follow all warnings and instructions marked on the audio equipment. [. . . ] Such chemicals will do irreparable damage to the disc's plastic surface. Discs should be returned to their cases after use to avoid serious scratches that could cause the laser pickup to "skip". Do not expose discs to direct sunlight or high humidity and temperature for extended periods. Do not stick paper or write anything with a ballpoint pen on the surface of the label side. 5 CONNECTIONS CAUTION : When you pull the plug out, make sure that the unit has been turned to POWER STANDBY first. LINE OUT jacks Connect these iacks to the CD input jacks on the amplifier : White pin-plug White jack (left) Red pin-plug Red jack (right) White White White 3. AC power cord Plug this AC power cord into a 120 Volt, 60 cycle grounded AC wall socket or the AC OUTLETS on the rear of the STR-84 or PLR-85 receiver. L R Red Red Red L R 2. REMOTE CONTROL jacks Connect the supplied remote control cable to the REMOTE CONTROL jacks as shown in the above diagram, Connect the other end of the cable to the rear of the matching STR84 or PLR-85 receiver. The remote control functions of this tape deck will only operate when connected to a matching Techwood STR-84 or PLR-85 receiver. IMPORTANT : A remote control is not included with this CD changer. 6 CONTROLS AND INDICATORS Front Panel 1. Disc Select buttons (1~5) There are five Disc Selection buttons numbered 1 through 5, each one corresponding to a numbered disc position on the disc tray. When your disc player is in playback mode, you can press one of these buttons to halt playing of the current disc and start playback of the disc whose number corresponds to the button you have pressed. 11. Disc Skip button The Disc Skip button located inside on top of the disc tray is used to rotate the disc tray to its next disc playing position in a clockwise direction. With each press of this button, the tray will advance one disc position. Repeat button This button is used for repeating one track, one disc or all discs. Pressing the Play button will start playback of all discs loaded onto the disc tray. They will be played in sequential order starting with the disc loaded into position one on the tray. Program button Use this button to program the order in which the selections are played. 13. Clear button Use This button to cancel the programmed playback. When pressed and held down, the Search Forward button allows the listener to fast forward to a particular musical passage on disc. When fast forwarding, sound will be heard and appropriate track and time information will be displayed. 6. Time button The Time button allows any one of four different types of tracking and time information to be displayed. Disc Tray Load a disc on this tray with its label side up while the tray is open. When pressed and held down, the Search Reverse button allows the listener to fast reverse to a particular musical passage on disc. As the disc is spinning in reverse, sound will be heard and appropriate track and time information will be displayed. 15. Pause button ( ) Pressing Pause button will halt playback of a disc temporarily with the display showing the Pause indicator and current track and time. Pressing the Play button again will resume playback starting from the current track and time on the disc. With each press of the Skip Forward button, the disc currently being played will advance to the beginning of its next track and resume playing. 16. [. . . ] Press the program button repeatedly until "END" appears on the display. Enter new tracks in the same way as normal programming after "END" disappears from the display. During playback, press the time button once and the time remaining on the track is displayed. Adding to any position: 1. Select the program number which you want to add a new track to by pressing the program button. [. . . ]