User manual TECHNICS SL-BD20 SERVICE MANUAL

[. . . ] • Basic and advanced features/operation are separated for easier reference. WARNING: TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS UNIT TO RAIN OR MOISTURE. Warning on lithium cell battery (for remote control unit) The battery used in this device may present a fire or chemical burn hazard if mistreated. Do not recharge, disassemble, heat above 100°C (212°F) or incinerate. Replace the battery with Maxell, Panasonic (Matsushita Electric), Sanyo or Sony CR2025; use of another battery may present a risk of fire or explosion. Ⅲ Do not disassemble and do not dispose of in fire. It is recommended that you . [. . . ] 45) is activated. EN White paper 51 Manual White Balance Operation If the camera is operating in Manual mode “ ”, perform Manual White Balance when shooting under various types of lighting. 1 SELECT OPERATION MODE ੬ 3 ENTER SETTING PLAY OFF CAME /PC Follow steps 1 through 5 of the white balance adjustment ( pg. Adjust zoom or position yourself so that the white paper fills the screen. stops blinking. 2 SET MANUAL WHITE BALANCE Lock Button •When the setting is completed, Power lamp DSC DS 4 EXIT MANUAL WHITE BALANCE ADJUSTMENT 5S RA Press MENU/SET. The indication “W. BAL. ” changes to “MANUAL” and only the Manual White Balance indicator is displayed. MENU/SET Dial Power Switch Display FOCUS EXPOSURE 4 W. BALANCE AUTO AUTO AUTO MANUAL LAY CP To Change The Tint For Recording . Red paper — deeper green; blue paper — orange; yellow paper — deeper purple. Recording Menu NOTES: Manual White Balance Adjustment ● In step 2, it may be difficult to focus on the white paper in some circumstances. ● A subject can be shot under various types of lighting conditions indoors (natural, flourescent, candlelight, etc. ). Because the color temperature is different depending on the light source, the tint of the subject will differ depending on the white balance settings. ● Once you adjust white balance during Manual White Balance operation, the setting is retained even if the power is turned off or the battery removed. 52 EN PLAYBACK Basic Playback For Video 1 LOAD A CASSETTE Slide OPEN/EJECT in the direction of the arrow, then swing the cassette cover open until it locks. Insert a tape and press “PUSH HERE” to close the cassette holder. Set the Power Switch to “ ” while pressing down the Lock Button. Then press MENU/SET, and the highlight bar automatically moves to “END”. •To set parameters for other functions, repeat steps 3 and 4. PLAY / Power lamp 2 ACCESS PLAYBACK MENU 3 SELECT FUNCTION OFF CAMER PC Y PLA 4 SET FUNCTION PARAMETERS FULL SOUND SOUND1 SOUND2 FULL SOUND SOUND1 SOUND2 ON OFF ON OFF ON OFF MENU/SET Dial Display 48kHz MODE 32kHz MODE SYNCHRO INDICATION DISPLAY TIMECODE 4 END FULL SOUND SOUND1 0. 0 ON ON OFF Playback Menu 4 48kHz MODE 32kHz MODE SYNCHRO INDICATION DISPLAY TIMECODE END FULL SOUND SOUND1 0. 0 ON ON OFF S DSC DSC A5 Power Switch 5 CLOSE MENU Press MENU/SET again, and the menu disappears. EN 55 Playback Sound During playback, the camcorder detects the sound mode in which the recording was made, and plays the sound back. (32 kHz is preset to “SOUND 1” and 48 kHz is preset to “FULL SOUND”. ) Recording sound 32 kHz Display FULL SOUND SOUND 1 SOUND 2 48 kHz FULL SOUND SOUND 1 SOUND 2 Stereo sound “L” sound is output on both channels “R” sound is output on both channels Stereo sound Output sound When watching a tape recorded at 32 kHz, if you want to change the output sound, access the Playback Menu and, in step 3 on page 54, select “32 kHz MODE” and set it for “FULL SOUND”, “SOUND 1” or “SOUND 2”. When playing back a tape recorded at 48 kHz, set in the same manner. NOTES: ● You can also use the provided RM-V713U remote control’s AUDIO MONITOR button to change the output sound (without having to access the Playback Menu). Make sure you point the remote control at the camcorder’s remote sensor. ● During playback, the camcorder detects the sound mode in which the recording was made. During playback the sound mode is displayed in the upper left corner. Display TIME CODE (Displaying The Time Code During Playback) You can display the Time Code on screen during playback. To turn it on, select “TIME CODE” at the Playback Menu and change the setting (੬ pg. OFF– The Time Code does not appear. TC 12 : 34 : 24 DEC 25 ’ 98 PM 5 : 30 Frames* Seconds Minutes *30 frames = 1 second DISPLAY (Displaying the Date During Playback) If the time has been set, the date is automatically recorded separately from the recorded video signal. To turn it off, select “DISPLAY” at the Playback Menu and change the setting (੬ pg. OFF– The date is not displayed. INDICATION TC 12 : 34 : 24 DEC 25 ’ 99 PM 5 : 30 32kHz/SOUND1 You can make the Playback Sound, Time Code and Date indications disappear. [. . . ] Do not write anything or put a sticker on either the front or back surface. If the CD-ROM gets dirty, gently wipe it with a soft cloth outward from the center hole using a circular motion. Keep it away from direct sunlight. EN Declaration of Conformity Model Number : CU-V501U Trade Name : TECHNICS Responsible party : US TECHNICS CORP. 07470 Telephone Number : 973-315–5000 This device complies with Part 15 of FCC Rules. [. . . ]