User manual TECHNICS SL-1200MK5

[. . . ] Turntable System Operating Instructions Model No. SL-1200MK5 SL-1210MK5 SL-1200MK5 Before connecting, operating or adjusting this product, please read these instructions completely. Please keep this manual for future reference. PP RQT7018-Y Dear customer Thank you for purchasing this product. For optimum performance and safety, please read these instructions carefully. SL-1200MK5 : Silver model SL-1210MK5 : Black model Supplied accessories Please check and identify the supplied accessories. [. . . ] ·Pitch can be instantly reset to the rated speed (33 1/3 or 45 r/min) with the reset button. Controls The direct drive produces high torque. ·Wow and flutter below 0. 01 %. Starting torque of 1. 5 kg-cm enabling the turntable to reach 33 1/3 r/min in 0. 7 seconds. ·Smooth stops are achieved with a fully electronic braking system. The braking speed can be adjusted with the brake speed control knob. -8 6 4 2 +8 2 4 6 +8 Tone arm with gimbal suspension ·Using the balance weight control measurement units on the tone arm, you can quickly change stylus pressure settings to the appropriate pressure. ·Stylus skipping can be reduced using horizontal weight control for scratch play. ·The tone arm can be finely adjusted in a range of 6 millimeters with the lockable height control. Anti-vibration design with 3 layer cabinet construction and large insulating legs. Pop-up stylus light. ·A light illuminates the stylus. Preparation of the cartridge 1 Attach a cartridge (not included). Follow the cartridge's instructions to correctly attach it to the head shell. ·Use the included shell weight when using a light cartridge (3. 5 to 6. 5 grams). Screws Head shell Shell weight Lead wire Terminal Cartridge Stylus 2 No. 8 Adjust the overhang. Fit the included overhang gauge to the head shell. Adjust the overhang and facing of the cartridge and tighten the screws. Screws Overhang gauge Stylus tip 52 mm 4 RQT7018 Putting the player together In order to prevent damage during shipping some of the equipment has been disassembled. ·Do not connect the AC power supply cord until set up is complete. ·Keep this unit as far as possible from speakers. ·Ensure the unit is not exposed to direct sunlight, dust, humidity, and heat from a heating appliance. ·This unit may pick up interference from a radio if there is one nearby. Keep radios as far as possible from this unit. Earth lead Adjusting the height of the insulators Place the unit where it is to be used and adjust the height of the legs to make the unit horizontal. ;; Audio mixer Preparatory adjustments Horizontal balance and stylus pressure 1 Release the tone arm. 1. Remove the stylus cover, taking care not to damage the stylus, then release the arm clamp. Free the tone arm from the arm rest. Arm clamp 3 Turn the stylus pressure control to "0" 1. Turn the stylus pressure control to "0". Hold the balance weight still while doing this. Balance weight ; Center line Turn stylus pressure control 2 Adjust horizontal balance 1. Turn the balance weight until the arm is approximately horizontal. Take care at this time not to allow the stylus to touch the unit. Balanced Arm clamp Too far forward Too far back 4 Adjust stylus pressure Turn the balance weight to adjust to the appropriate pressure for the cartridge you are using. See the cartridge's instructions for recommended stylus pressure. Stop when the center line points to the required pressure. Arm clamp Arm rest Cue lever Center line Anti-skating control Turn balance weight 6 RQT7018 Preparatory adjustments Using the balance weight control Make note of the balance weight setting for your stylus cartridge, you can quickly change the stylus pressure without having to readjust the horizontal balance of the arm each time you remove and re-attach the stylus cartridge. [. . . ] ·Use a good quality record cleaner to keep your records clean. Head shell terminals Wipe the head shell terminals occasionally. Use a soft cloth. ·Damage to your speakers can occur if the head shell is moved while the volume is turned up. ·Leave the stylus cover on while handling the head shell to prevent damaging the stylus. Product information For product information or assistance with product operation: In the U. S. A. , contact the Panasonic Customer Call Center at 1800-211-7262, or e-mail consumerproducts@panasonic. com, or the website (http://www. panasonic. com). Customer Care Centre at 905-624-5505, or visit the website (www. panasonic. ca), or an authorized Servicentre closest to you. Oiling the center spindle. Apply 2 or 3 drops every 2000 hours of operation. [. . . ]