User manual TECHNICS RS-B605

[. . . ] 4 Part names . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Installing batteries in the remote control unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Watching TV Watching a TV programme . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Operating the TV buttons . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] Remove the batteries if weak or if the unit is not in use for long periods. Incorrect installation of the batteries may damage the remote control. E6 ENGLISH Part names Part names TV set TV front POWER 8 Power switch Turns on and off the main power. Power indicator Power can be turned on by the remote control when the indicator is red. 8 On timer indicator 23 Power save indicator 20 Infrared sensor window Receives the infrared wave from the remote control. 6 Behind the door PRESET / MENU CH VIDEO (MONO) L-AUDIO-R AV-3 IN PRESET/MENU 12 27 Audio input terminals (AV-3) Connects to a camcorder, video game, etc. PRESET/MENU button Tunes the channels. Makes adjustments in PRESET. CH 8 27 Video input terminal (AV-3) Connects to a camcorder, video game, etc. / CH 8 9 Headphone jack Use to listen to the audio with headphone. Channel up/down button Selects the channels. Tunes or sets the channels. · When using headphone, see 9. E7 Watching a TV programme TV Set Simple operations for watching a TV programme 1 POWER Turn on power. · When the power indicator is off, press POWER . · When the power indicator lights up red, press on the remote control. The power indicator changes to green and a picture appears. Power indicator Behind the door 2 Select channel. With CH / CH PRESET / MENU CH CH CH · Press CH and channels change as shown below. / 2 / 1 / 0 . . . With the number buttons (on remote control) 5 · To select a one-digit channel, such as 5, press . If "5-" is indicated, press to select one-digit input, and then 5 press again. · To select a two-digit channel, such as 15, press to select 1 5 the two-digit input. Press , and then press . TV/VIDEO 1 4 7 2 5 8 0 CH CH 3 6 9 1 5 CH MENU -115 PAL B/G CH AV MODE NORMAL POWER SAVE 3 Adjust volume using . / TV · The number of oval blocks " " indicates the volume level. The volume bar disappears approximately three seconds after the volume has been adjusted. VOLUME 10 · When the power indicator lights up red, either CH / CH on the TV can be pressed to turn on the power. To turn off SKIP, press the number buttons to select the desired channel and then set "SKIP" to "OFF". · FINE The frequency changes to allow fine tuning. 6 Press MENU until normal screen appears. · When you select AV1, AV2 or AV3 for the channel position, the CHSETTING menu changes as shown on the right and the colour mode changes in the following order: AUTO PAL SECAM N443 CH-SETTING POSITION COLOUR AV1 AUTO CH SELECT ADJUST MENU RETURN N358 · Switching COLOUR system: Set the system to "AUTO" for normal TV reception. The AUTO mode automatically detects the receiving signal system and changes the reception system of the TV set. When the picture is not stable, switching to an appropriate system may improve the picture quality. · In a weak reception area, or under bad reception conditions, you can change the frequency by fine tuning. · When using FINE, the channel number changes from green to yellow. · To return the channel to its original frequency setting, follow the manual channel tuning procedure. See 15 . E 16 ENGLISH Settings and adjustments Picture adjustment TV/VIDEO 1 2 CH CH Press screen. MENU to call MENU MENU PICTURE SOUND FEATURE TIMER CH-SETTING 1 4 7 2 5 8 0 CH CH 3 6 9 CH Press / select "PICTURE". CH to 3 MENU Press / display PICTURE menu. CH CH Press / select adjustment items. to PICTURE CONTRAST COLOUR BRIGHTNESS TINT TECHNICSNESS PICTURE NR WHITE TEMP (STANDARD) 50 0 +10 - 10 ON 20 (STANDARD) MENU AV MODE NORMAL POWER SAVE 4 5 to NORMAL Adjust using / . TV · Wait for approximately three seconds to return to PICTURE menu. CONTRAST - 50 + 6 7 Repeat steps 4 and 5 above to adjust other items. Press MENU until normal screen appears. · When NORMAL is pressed while the PICTURE menu is displayed, the setting for the selected item is reset to the standard (factory setting) position. · When NORMAL is pressed while the MENU screen is displayed and "PICTURE" is selected, all the settings for the PICTURE items are reset to the standard (factory setting) position. The following table lists the adjustment items shown in the PICTURE menu and how they change as you / . press Selected item CONTRAST COLOUR BRIGHTNESS TINT -1 TECHNICSNESS PICTURE NR -2 WHITE TEMP To more reddish background Press To decrease contrast For less colour intensity For less brightness To move tint toward purple For less sharpness Press - + + + ON OFF + To increase contrast For more colour intensity For more brightness To move tint toward green For more sharpness (See note below) To more bluish background *-1: TINT can only be selected and adjusted when receiving NTSC broadcasts. [. . . ] Power is automatically turned on five minutes before the preset length of time expires. The TV set automatically returns to the Standby mode after the preset time. · The Reminder is cancelled if POWER on the TV set is pressed or if the power is otherwise interrupted. · To cancel the timer setting, press NORMAL when " " is displayed on the left of " " so as to set the timer to "- - : - -". E 24 ENGLISH Connections Connecting to a DVD player The DVD input terminals (COMPONENT-IN) on the rear of the TV can be used to input high-quality images from a DVD player. DVD input terminals Red: To AUDIO (R) White: To AUDIO (L) AV-2 IN COMPONENT Y Green: To Y Blue: To PB (CB) Red: To PR (CR) PB (CB) TV To audio out (L/R) terminals PR (CR) To colour-difference (component video) out terminals DVD player Connecting the video terminals OUT AV-1 IN AV-2 IN COMPONENT Y S-VIDEO (AV-1 IN) VIDEO L AUDIO (MONO) PB (CB) PR (CR) R DVD input terminals Y COMPONENT-IN VIDEO PB (CB) PR (CR) DVD player Y or Y/Y PB (CB) or B-Y/Pb PR (CR) or R-Y/Pr Watching DVD Playback TV/VIDEO TV/VIDEO 1 COMPONENT 1 4 7 2 5 8 0 CH CH 3 6 9 Press TV/VIDEO to select "COMPONENT", DVD input screen. MENU 2 AV MODE NORMAL POWER SAVE Turn on the DVD player and begin playback. TV · When connecting the TV to a DVD player via the Component-in terminals, the video and audio from the DVD player cannot be output through the Audio/Video out terminals on the TV. [. . . ]