User manual TECHNICS RS-B10

[. . . ] IN NO EVENT SHALL TECHNICS BE LIABLE FOR SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES OR FOR LOSS OF PROFITS OF DEALER OR CUSTOMERS OF ANY PRODUCT. Requests This Operation manual has been carefully prepared for your easy understanding. However, please do not hesitate to contact a distributor in your district or our office if you have any inquiry. Description contained in this Operation manual are subject to change without notice for improvement. In the case where this Operation manual should be illegible due to destruction or lost by fire or breakage, purchase another copy of the Operation manual from our office. [. . . ] To avoid such trouble, be sure to perform cleaning frequently. 4-4 Routine Maintenance Opening the maintenance cover Remove a maintenance cover to clean the inside of the printer. It is necessary to remove the appropriate one of the right and left maintenance cover, depending on the part to be cleaned. After removing the maintenance cover, take care not to touch the reading surface of the linear encoder scale. In addition, take care that the reading surface is not soiled or scratched. The print quality may be degraded if skin grease adheres to the wiper. Do not touch wiper with your bare hand. Wiper Linear encoder scale 4-5 4 Daily Maintenance STEPS: 1 Remove the top two screws for the maintenance cover. 2 With the shaft of the frame as the fulcrum, turn over the maintenance cover toward the front so that it is placed in the vertical position. 3 Pull out the maintenance cover upward. 4-6 Cleaning the wiper and ink caps [CARRIAGE OUT] Cleaning the wiper and ink caps [CARRIAGE OUT] The ink caps prevent the nozzles in the heads from drying and thus being clogged. As the printer is used, the wiper and ink caps gradually become stained with ink and dust. If nozzle missing cannot be corrected even after executing the CLEANING function (Refer to "If the printed pattern is abnormal (Cleaning) (p. 3-29)" ) , use Cleaning kit and cotton swab. T Tools necessary for cleaning. When solvent ink is used Cleaning solution (SPC-0369) Goggle When water-based ink / sublimation transfer ink Sb51 is used Cleaning Liquid Bottle Kit A29 (SPC-0137) Goggle You are recommend to perform cleaning frequently in order to maintain a high image quality and keep the printer in good condition. When cleaning the ink station or heads, be sure to wear supplied gloves (When solvent ink is used) and goggle . If you do not use the goggle, you may get ink in your eyes. Do not move the carriage out of the capping station by hand. There may be a chance that the ink discharge passage can be clogged with coagulated ink. (When solvent ink is used, clean once a week. ) Be sure to wear the supplied goggle and gloves. The ink contains an organic solvent. If ink settles on your skin or gets in your eyes, immediately and completely wash them off with water. (When solvent ink is used) Do not move the carriage out of the capping station by hand. When the [DISWAY WASH] function is executed, there may be a case where the cleaning liquid keeps staying in the caps without flowing out. If the pump is clogged, contact your dealer or a sales office of TECHNICS. STEPS: 1 Make sure that the printer is in LOCAL mode, and then press the [ST. MAINT] key. If it is in REMOTE mode, press the [REMOTE] key. L. > [JV5-01] width : mm ST. MAINTENANCE CARRIAGE OUT <ent> 2 Select [DISWAY WASH] by pressing the [ key. 3 times ] key three times and press the [ENTER] The carriage will come out of the capping station. Idle suction is performed in cycles of 5-second suction followed by 10-second pause. ST. MAINTENANCE DISWAY WASH <ent> If there is a problem with the waste ink tank, the display will show either of the following messages. Follow the displayed instructions to restore the normal conditions. No waste ink tank, or a tank is FULL. <ENT>keyHIT is after theTANK set or exchg Replace a waste ink tank. [. . . ] (0 ~ 90 min (In steps of 10 minutes) ) StandbySwitchoverTIM NONE, 0 - 90 min [1] HEATER SET TIME <ent> STANDBY 10 min : OFF TIME : NONE 6 Press the [END] key several times. The printer returns to LOCAL mode. L. > [JV5-01] width : mm 6-32 How to operate function menus How to operate function menus The following pages show the operating procedures and the messages displayed on the LCDs, using the following icons. For detailed information of operation procedures, refer to the relevant pages. Icon Description This icon means pressing the [FUNCTION] key once. This operation is used to enter [FUNCTION mode] or to go to the lower level of hierarchy. [. . . ]