User manual TEAC T-R680RS

[. . . ] 9A10358500 Z T-R680RS AM / FM Stereo Tuner OWNER'S MANUAL WARNING: TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE. CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance. CAUTION < DO NOT REMOVE THE EXTERNAL CASES OR CABINETS TO EXPOSE THE ELECTRONICS. < IF YOU ARE EXPERIENCING PROBLEMS WITH THIS PRODUCT, CONTACT TEAC FOR A SERVICE REFERRAL. [. . . ] In these cases, press the RESET switch once or twice with a pencil or a ball-point pen lightly. All the settings kept in memory (such as preset stations) will be erased. A LINE OUT jack Analog 2-channel audio signal is output from this jack. Connect this jack to the TUNER input jack of the amplifier with an RCA cable. Make sure to connect : white plug q white jack (L: left channel) red plug q red jack (R: right channel) Voltage Conversion B RS-232C connector See page 14 for details. C Power cord (AC) Be sure to connect the power cord to an AC outlet which supplies the correct voltage. Be sure to remove the power cord from the AC outlet before repositioning the voltage converter switch. Using a flat-bladed screwdriver, set to the appropriate 230V or 120V position according to your area. IN NORTH AMERICA USE ONLY ON 120 V SUPPLY. 5 Unit Functions A B C D EFG H M LKJ I A B K C I H G Note: To simplify explanations, instructions in this manual refer to the names of the buttons and controls on the front panel only. Associated controls on the remote control will also operate similarly. 6 Remote Control Unit A POWER (STANDBY/ON) Press this switch to turn the unit on or standby (clock mode). When using the remote control unit, press the ON button to turn the unit on, and press the STANDBY button to turn it standby. The equipment draws a nominal amount of power from the AC outlet even with its POWER switch in the OFF position. The provided Remote Control Unit allows the unit to be operated from a distance. When operating the remote control unit, point it towards the remote sensor on the front panel of the unit. < Even if the remote control unit is operated within the effective range (5m), remote control operation may be impossible if there are any obstacles between the unit and the remote control. < If the remote control unit is operated near other products which generate infrared rays, or if other remote control devices using infrared rays are used near the unit, it may operate incorrectly. Point the remote control unit at this sensor when operating the remote control unit. 7 Radio Reception FM MODE Button 1 3 4 2 1 Press the POWER switch (or ON button of the remote control unit) to turn the unit on. Pressing this button alternates between Stereo mode and Mono mode. 2 Select AM or FM by pressing the corresponding button. Stereo FM stereo broadcasts are received in stereo. The "STEREO" indicator lights on the display when an FM stereo broadcast is tuned in. < If the sound is distorted and the "STEREO" indicator light flashes, the signal is not strong enough for good stereo reception. Reception will now be forced monaural, reducing unwanted noise. 3 If the PRESET indicator is lit, press the TUNING MODE button to select the manual tuning mode. This button is used to change the tuning mode. 4 Select the station you want to listen to (auto selection). Hold down the TUNING button for 0. 5 to 2 seconds. Selecting stations which cannot be tuned automatically (manual selection) Hold down (or repeatedly press) the TUNING button and release it when the station you want to listen to is found. When the TUNING button is pressed momentarily (0. 5 second or less), the frequency changes by a fixed step. < "TUNED" is displayed when a broadcast is correctly tuned in. 8 Direct Tuning Sleep Timer The power can be switched off after a specified amount of time. Press the SLEEP button repeatedly until desired time appears on the display. [. . . ] The unit will turn on with the station you selected last time. Though the broadcast is stereo, it sounds monaural. e Press the POWER switch (or the ON button of the remote control unit) to turn the unit on. e Use remote control unit within the range (5m /15ft) and point at the front panel. If normal operation is not restored, unplug the power cord from the outlet and plug it again. < When you don't use the timer, press the TIMER button to turn it off. [. . . ]