User manual TEAC QUICK DV-W512GK

[. . . ] TEAC DV-W512GK Drive Quick Installation Guide The TEAC DV-W512GK is a modern high performance CD-R / CD-RW drive. 5 degrees out of the vertical or 10 degrees out of the horizontal position. When the drive is vertical mounted an 80mm disc cannot be played. Caution: Use of controls or adjustments or performance of procedures other than those specified herein may result in hazardous radiation exposure. [. . . ] The installation position is not allowed to be tilted more than - X - Slave: The drive is configured as second IDE drive. If there is only one hard disk in the PC the optical drive can be operated at the same IDE connection parallel to this hard disk. Important: The data rates of both devices may be decreased. X - - Cable Select: Master/slave detection is achieved by the controller. Installation and Connection Very important: Switch off your PC and any attached devices and disconnect the power cord(s). Do the same if the optical drive is reconfigured. Important: If your PC will not start up correctly switch it off immediately and check all of the connections and jumper settings. Controls and Functions at the Front Panel Busy-LED (1) Open the case of your PC and lift it off carefully. (3) Locate a free slot for 13. 3cm / 5. 25" drives and install the Drive using the provided four screws. Emergency Eject Eject Key Important: Do not use screws which are longer than 5 mm! Headphone Jack Volume-Control (4) Connect the power cable and the 40-pin data cable (assure the correct orientation, pin 1 is often marked with a color stripe) to the drive. (5) Connect the provided audio cable to the sound card. ON/BUSY indicator The indicator LED light in Seek, Play, Read, and Write operation. In the following table you will find a list including a description of the different drive states and their associated indicator states. Cleaning and maintenance of your TEAC Drive Usually sound cards offer more than one connector to connect an audio cable to. Please refer to the manual of the sound card to find the connector in question. Usually there are only problems with dirty or defective CD. Important: Do not use cleaning CDs which will remove dirt of the lense of the laser aided by a little brush. Any of these methods may cause damage to your Drive. Handling: Check the CD before inserting it into the drive. Especially at high reading velocities dirt may increase the number of reading errors. Audio-Cable 40-pin Datakabel Power Cable Very important: Shape CD/DVD, a kind of CD/DVD which is not shaped like the normal round CD/DVD, are not allowed to be used in this drive. Otherwise rotational forces may cause severe damage to the drive. (6) Close the case of the PC. Do not forget to connect other devices and accessories if there are any. (7) Connect the PC to the wall outlet and switch it on Installing Drivers and the Writer Software As a general precaution the installation of the hardware has to be carried out as described before. The software installation starts with activating the reading functionality of the drive as this is well known with any conventional CD-ROM drive. [. . . ] supported DVD-R/CD-R madia speed or data transfer rate of the PC) 4 Drive performance Data transfer rate (Asyncronous transfer) Access time Starting time from power on Programmed I/O: 16. 6MB/s max. (Default: ULTRA DMA Mode-2) DVD-ROM: 160ms typical (random stroke) CD-ROM : 160ms typical (random stroke), by TEAC standard 18sec of less (average) (excluding the multisession photo CD), by TEAC standard 2MB Block/10-15bits (DVD-ROM) Block/10-12bits (CD-ROM Mode-1) Block/10-9bits (CD-ROM Mode-2, ECC off) Auto eject or Auto Load 1 x green LED Stereo mini-jack 0. 7+/-0. 2Vrms 33Ohm Thumb wheel knob +5V, +12V IDE (ATAPI): ATA/ATAPI-5 Line out 0. 85+/-0. 15Vrms 47kOhm Mode setting straps (Master) Temperature 5 to 45degC, Hummidity 15 to 80% (non-condencation) Temperature -40 to 60degC, Hummidity 15 to 95% (non-condencation) 148. 4mm x 42. 2mm x 170. 0mm (Include the Standerd Bezel) 900g UL, TÜV, FCC, CE 70, 000 POH (duty 25%) Warranty is provided under the terms of the TEAC warranty conditions. In case of warranty: www. teac. de/support 5 6 Data read error rate Front panel Button Indicator (LED) Headphone output Volume control 7 Rear panel Power supply Interface connector Audio output Strap switch 8 Operating environment Place of operation Place of storage 9 Dimensions/weight Dimensions (WxHxD) Weight 10 11 Safety standards Reliability: MTBF [. . . ]