User manual TEAC NS00010A

[. . . ] The Microserver will be ready when the Power LED stops flashing and stays solidly lit. If necessary, launch the Vendotto Manager software again to re-detect the NAS Microserver. serial port: Connects to (a) an external analog modem (9-pin, female connector) or (b) the system reset key, which enables you to restore default settings. Using the system reset key will delete all configuration settings, user definitions, and user profile information. [. . . ] Vendotto Manager will assign a temporary IP address to the TEAC NAS Microserver, configuring the unit as a DHCP client using default settings, and then display a message (Figure 5) informing you of the temporary IP address. Note: The temporary IP address will be deleted automatically in about two hours. Before time expires, you must establish a static IP address using the Basic Setup menu in Vendotto Manager's WebTool (Figure 8). Select [Obtain an IP address automatically] if there is a DHCP server on your network. If there is no DHCP server on your network, select [Specify an IP address] and enter an IP address and subnet mask (i. e. , IP address: 192. 168. 11. 100, Subnet mask: 255. 255. 255. 0). 8 5 TEAC NAS Microserver Installation Guide (this document) Technical Support For technical support, please contact the TEAC Service and Support Center: floppy disks (2) AC adapter Power cable TEAC America, Inc. (USA) Technical Support Telephone: (323) 727-4860 · Fax: (323) 869-8751 Monday - Friday 8:00 a. m. - 5:00 pm PST http://www. teac. com/DSPD/techsupport. htm E-mail: dspdtsg@teac. com Vertical product stand Warranty TEAC NAS Microserver System reset key Figure 1. NAS Microserver Package Contents Note: If any of the items above is missing from your kit upon purchase, please contact your vendor immediately for a replacement kit. Front and Rear Panels Figure 4 illustrates the front and rear panels of the TEAC NAS Microserver. LAN COM USB PRINTER LAN DC IN 19V TEAC AD-8019(V) ONLY GND This product is warranted by TEAC America, Inc. LENGTH OF WARRANTY ­ This warranty will be effective for both labor and parts, and this warranty will be effective for one (1) year from the date of original purchase. WHO MAY ENFORCE THE WARRANTY - This warranty is valid only in the United States, and enforceable only by the original purchaser. Damage resulting from failure to follow instructions contained in your user's manual. Damage occurring during shipment of the product (claims must be presented to the carrier). Damage resulting from repair or attempted repair by anyone other than TEAC Service Department. Damage resulting from modification or attempted modification of product not authorized by TEAC. Damage resulting from causes other than product defects, including lack of technical skill, competence, or experience of the user. Damage to any unit which has been altered or on which the serial number has been defaced, modified or removed. For wireless configurations, TEAC cannot be responsible for interference or operation in locations that restrict range. HOW YOU CAN GET WARRANTY SERVICE ­ Please contact TEAC service department for Return Authorization number before shipping unit(s) to TEAC. Information required for R/A request should include your name and/or company name, telephone number, TEAC model, version and serial number(s). Return Authorization (R/A) number must be clearly marked on the outside of each carton shipped to TEAC. Return merchandise must be packed in original shipping containers or otherwise packed adequately to prevent damage in shipment. You are responsible for all risk of damage to or loss of merchandise in transit to TEAC. TEAC reserves the right to reject any merchandise that is not packaged and/or marked as instructed hereon. [. . . ] If a wireless LAN card is not already installed in your PC, you will need to install one to enable wireless communication. ) For more information, refer to the TEAC Vendotto Operation Manual. Installing the Vendotto Manager Software Insert the floppy disk that contains the Vendotto Manager software into a floppy disk drive on the host setup computer, which must be connected to the network. Double-click the Setup. exe icon, and follow the instructions on screen to complete the installation. 4 9 OK button User Name field NAS Microserver entry WebTool button Figure 7. Vendotto Manager Displaying New IP Address 6. In the User Name field, key in Admin. This field is case-sensitive, so be sure to capitalize "A. " Leave the Password field blank. Click the OK button (Figure 7). Double-click on the NAS Microserver name [NAS] (Figure 5). Vendotto Manager will launch your system's web browser (Internet Explorer is used in these examples) and access the Vendotto WebTool on the Internet. [. . . ]