User manual TASCAM US-2000

[. . . ] D01088620A US-2000 USB 2. 0 Audio Interface OWNER'S MANUAL IMPORTANT SAFETY PRECAUTIONS CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). The lightning flash with arrowhead symbol, within equilateral triangle, is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance. This appliance has a serial number located on the rear panel. Please record the model number and serial number and retain them for your records. [. . . ] If the disc becomes scratched or dirty, your computer may be unable to read it and the software cannot be installed. If the disc becomes unreadable, a fee will be charged for its replacement. Never attempt to play the enclosed CD-ROM in a conventional audio CD player, as the resulting noise may damage your speakers or your hearing. Windows Windows XP 32-bit SP2 or later Windows XP 64-bit SP2 or later Windows Vista 32-bit SP2 or later Windows Vista 64-bit SP2 or later Supported computer system: Windows compatible computer with a USB 2. 0 port · · CPU/clock: Pentium 4 1. 4 GHz or faster AMD Athlon 1. 4 GHz or faster (or equivalent processor) · Memory: 512 MB or more for Windows XP 32-bit and Windows Vista 32-bit 1 GB or more for Windows XP 64-bit and Windows Vista 64-bit NOTE Although this product has been checked for use with typical computers that meet the above operating requirements, we cannot guarantee that it will operate with all computers that meet these requirements. Please be aware that even under the same conditions, processing capability may vary depending on differences of the design and system. Installing the driver for Windows NOTE · During driver installation, a warning that "this software . . . This message appears when a driver that has not received Windows Logo testing is installed. This message appears because the drivers for TASCAM products have not received Windows Logo testing. If this message appears, click Continue to proceed with the installation. During installation, you must connect, disconnect and reconnect the unit in steps 7, 8 and 9. You should complete each of these installation steps in less than one minute. Installation may fail if you take too much time. · 1 Confirm that the unit and the PC are not connected by the USB cable. 2 Insert the included driver installation CD-ROM into the PC where you will install it. 3 Click the "Install Driver" button when the screen below appears. (If this screen does not appear automatically, find and open the "Autorun2. exe" program in the "Autorun" folder on the driver CD-ROM. ) Mac OS X Supported operating system: Mac OS X 10. 4. 11 or later Mac OS X 10. 5. 6 or later Supported computer system: Apple Macintosh series equipped with a USB port as standard equipment · CPU/clock: Power PC G4 1 GHz or faster, or Intel processor · Memory: 512 MB or more Installing the driver In order to use the US-2000, you must install the appropriate driver into your computer. As described below, this is an easy process using the CD-ROM included with the US-2000. You can download the most recent version of the driver from the TASCAM website <http://www. tascam. com/>. 4 When the language selection screen (below) appears, select the language you prefer and then click the "OK" button. TASCAM US-2000 9 3 - Installation 5 Click the "Install the Driver" button when the screen below appears. 9 When the screen below appears once more, reconnect the unit and the PC with the USB cable. 6 Read the contents of the License Agreement, and select "I accept the agreement" if you agree to the terms. Next, click the "Install" button to start installation. 10 When the screen below appears, the installation is complete. Click the "Reboot now" button to restart the PC to use the driver. 7 When the screen below appears, use the supplied USB cable to connect the unit to the PC. 8 When the screen below appears, unplug the connecting USB cable from the unit or the PC. 11 After the PC has restarted, open the "TASCAM US-2000" ("Start > Control Panel") or "US-2000 Control Panel" ("Start > All Programs > TASCAM"). If the Driver Version, Device and other data appear correctly, the installation has succeeded. 10 TASCAM US-2000 3 - Installation Installing the driver for Mac OS X 1 Confirm that the US-2000 is not connected to the computer. As the "TASCAM_ US-2000_x. xx" is created on the desktop, open the folder. 3 Dboule-click the "TASCAM_US-2000_x. xx. mpkg" in the folder to launch the installer. [. . . ] Set "Default Input, " "Properties for, " "Default Output" and "System Output" to "US-2000. " 3 Launch iTunes, select an audio file and start playback. Cubase LE4 For details see the provided Cubase LE4 Quick Start Guide. 16 TASCAM US-2000 7 ­ Troubleshooting Please read this chapter if you are unable to use the unit properly even after setting it up following the procedures in this manual. If you are still unable to resolve your problems please contact TASCAM customer support with the following information about the operating environment and details about the trouble. Operating environment · Computer manufacturer: If you make the following settings, sound will be output through this unit, but no sound will be output by the computer's speakers or headphone jack. Windows XP 1 Shut down all applications, and open the "Control Panel" from the "Start Menu. " 2 Open "Sounds and Audio Devices" NOTE If you cannot find the above item, click "Sounds, Speech, and Audio Devices" and it will appear. · Model: · CPU: · Installed memory: · OS: · DAW: · Antivirus software use: · Wireless LAN use: ª 3 Click the "Audio" tab, and set the "Default device:" for "Sound playback" and "Sound recording" to "TASCAM US-2000. " Windows Vista 1 Shut down all applications, and open the "Control Panel" from the "Start" menu. 2 Open "Sound. " NOTE If the above item does not appear, click "Hardware and Sound" and it will appear. Installation is failing. Installation completed, but the computer does not recognize it. If some trouble is causing installation to fail, or installation completes but the computer does not recognize the unit, check the following. If the USB indicator is not lit, confirm that the USB cable is properly connected. NOTE Always use the included USB cable. 3 Click the "Playback" tab, right-click "Speakers US-2000" and click the "Set Default" button. Mac OS X 1 Shut down all applications and open "System Preferences" from the Apple menu. 2 Open "Sound. " 3 From the "Output" tab, select "US-2000: Output. " 2) Change the USB port Since the unit may not properly function with some USB ports, try connecting to a different (built-in) USB port, and reinstall the driver. NOTE After completing the settings, restart the computer and check the playback sound. [. . . ]