User manual TASCAM TEAC CD-W512S

[. . . ] Various operations are indicated as per the following table: Operation At tray loading At tray eject During write/erase During audio play During seek/data transfer Left LED off off green LED flashes off off Right LED green LED flashes green LED flashes off green LED flashes green LED lights emergency eject mechanism: If the eject button fails, you can turn off the power to the CD-RW drive and insert a small, thin rod (such as a straightened paper clip) into the emergency eject mechanism opening and press firmly to eject the disc. Caution: Do not attempt to use the emergency eject mechanism when either the Power or Busy indicator is lit or you may seriously damage the disc or the CD-RW Drive. (Some CD-ROM titles disable the manual eject button and rely on software commands to eject the disc. [. . . ] For example, to set the CD-Recorder to SCSI ID 5, you would place jumpers on jumper pin pairs S0 and S2. The factory default setting is SCSI ID 3 (S0 and S1 closed). SCSI ID 0 1 2 3 4 5 6 7 0 Open Close Open Close Open Close Open Close 1 Open Open Close Close Open Open Close Close 2 Open Open Open Open Close Close Close Close SCSI ID Parity Switch Termination "S" numbers Factory use only. jumper pin configuration block TEAC CD-RW Installation Guide 4 Terminating the CD-RW Drive Terminating the CD-RW Drive If you position the CD-RW drive at the end of a SCSI chain, you must "terminate" the CD-RW drive; however, do not terminate the CD-RW drive if it is not physically connected at the end of the SCSI chain. If jumper pin S4 is closed (that is, if the jumper is seated on both pins), the CD-RW drive is terminated. If S4 is open (i. e. , the jumper is not seated on both pins), the CDRW drive is not terminated. The factory default setting for the CD-RW drive is closed (terminated). Warning: Failure to correctly terminate the SCSI bus may result in malfunction to the CD-RW drive. Configuring Other Jumpers on the CD-RW Drive This section explains how to configure the remainder of the jumper pin block on the rear panel of the CD-RW drive. Setting the Parity Switch If jumper pin S3 is open, an odd parity check is performed for the input data. Jumper Settings S5 and S6 These jumper pins are intended for TEAC factory use only. The factory default setting is open. Installing the CD-RW Drive After you install a SCSI adapter card in your computer and configure the jumper pin block on the CD-RW drive, follow the steps below to install the TEAC CD-RW drive into your computer. Refer to your computer documentation for information specific to your system. Turn off the power to the computer system and any external devices connected to it. This will prevent damage to the computer or CD-RW drive that may be caused by a discharge of static electricity. Remove your computer's cover, faceplate, or 5. 25-inch bay cover, as well as mounting clips, screws, and retaining brackets. Install the CD-RW drive in an orientation within ±10° of horizontal. Secure the drive using 3x5mm mounting screws. TEAC CD-RW Installation Guide 5 Installing the CD-RW Drive Warning: Do not use mounting screws longer than 3x5mm to secure the CD-RW drive or you may damage the unit. secure drive with 3x5mm screws 5. Connect the CD-RW drive to the SCSI host adapter card using a 50-pin interface ribbon cable. Be certain to connect pin 1 on the CD-RW drive to pin 1 on the SCSI adapter card. (Pin 1 on the interface cable is usually designated by a color stripe along one edge of the cable. Also, the interface ribbon cable connector may feature a tab on one side. [. . . ] Refer to "Recommended Software" on page 8. TEAC CD-RW Installation Guide 7 Recommended Adapters Recommended Adapters You must install a SCSI adapter card in the host computer to utilize the CD-RW drive. For optimum performance, TEAC recommends a PCI bus master SCSI adapter card (such as an Adaptec AHA2940 or equivalent). Please refer to the SCSI adapter card documentation for installation instructions. Recommended Software Before you can record data onto CD-R or CD-RW discs using your TEAC CD-RW drive, you must first install pre-mastering or packet-writing software onto your computer's hard disk. [. . . ]