User manual TASCAM MD-CD1MKIII

[. . . ] D01142520A MD-CD1@$ Minidisc Deck/CD Player OWNER'S MANUAL IMPORTANT SAFETY PRECAUTIONS The labels required in this regulation are shown at 1 and 2. 2 1 CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). The lightning flash with arrowhead symbol, within equilateral triangle, is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance. 21503-W WARNING: TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE. ª For U. S. A. TO THE USER This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. [. . . ] Refer to "Display master and remote control master" on page 22. To prevent operation errors, we recommend that the display master and the remote control master be set for the same deck. The Search function does not operate with data CDs. TASCAM MD-CD1MKIII 27 7 ­ CD and MD Playback Time Search function By specifying time from the start of a certain track, you can start playback from a specified point of a specified track. NOTE Following the above example, if "0021" is input, the same position will be located. Auto cue When the auto cue function is turned on, when a track is selected, the point where sound begins (not where the track begins) on that track is located, and the unit enters playback standby mode. Then, when the PLAY button is pressed, playback begins at exactly that point. Auto cue on/off and the sound start position detection level can be set separately for CD and MD. NOTE Basic operation 1 During stop, playback or playback standby modes, use the number buttons on the remote control to input the three-digit track number (such as 002 for track 2), then the desired elapsed time (***min **sec) from the start of that track. Example: To specify 1 min 30 sec from the start of track 2, input "002 001 30. " NOTE · This function is not available in random playback mode, program playback mode, or group playback mode. However, if you input the three-digit track number, playback will begin from the start of that track. · Regardless of the time display mode, the time from the start of the specified track is displayed. When the final digit is entered, the desired position is automatically located. During stop or playback modes, playback will begin from the desired point. During playback standby mode, at the desired point the unit will enter playback standby mode. NOTE · Auto Cue functions only for MD tracks recorded in the ST mode. For MD tracks recorded in MONO, LP2 or LP4 modes, the Auto Cue function will only cue to the very beginning of the track. · During the stop mode, to cue to the start of sound on track one, just press the READY button. Turning the Auto Cue function on and off Press the AUTO CUE button on the remote control to turn this function of display master on and off. option on the PLAY submenu of the MD menu or CD menu to turn the Auto Cue function on and off for each deck. (Default position: OFF) When the Auto Cue function is on, A. CUE is lit on the display. Even when the power is turned off, the Auto Cue setting is maintained. option on the PLAY submenu of the MD menu or CD menu to set the sound start position detection level. The level can be set between ­72 dB and ­24 dB in 6 dB increments. NOTE If a point which does not exist is selected, setting operation will be cancelled. Operation variations Even if the final second is not input, playback will begin from the selected point after pressing the PLAY button. Or, if you press the READY button, the unit will enter the playback standby mode at the selected point. Track search This is explained in the "Specifying by track number" part of "Track selection" on page 27. After inputting the three-digit track number, press the PLAY button to begin playback of that track, or the READY button to cue the track and enter playback standby mode. Specifying to the minute After inputting the three-digit track number and the number of minutes after the start of the track, press the PLAY button to begin playback of that track, or the READY button to cue the track and enter playback standby mode. [. . . ] In order to properly record the cueing positions between tracks, space of a certain length is created. If such spaces between tracks are not desired, make the following settings before dubbing. · Connect the CD digital output to the MD digital input (either the optical or the coaxial terminal) · Select OPTICAL or CIAXIAL as the input source · In the REC sub-menu of the MD menu, set the SYNC MODE option to ON Track numbers are not properly entered. When recording a CD through a digital connection, short tracks are sometimes created depending upon the recorded content of the CD. [. . . ]