User manual TASCAM M-164UF

[. . . ] D01083020A M-164 M-164FX M-164UF Analog Mixer OWNER'S MANUAL IMPORTANT SAFETY PRECAUTIONS CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). The lightning flash with arrowhead symbol, within equilateral triangle, is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance. For U. S. A. TO THE USER This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. [. . . ] These jacks are balanced, but they can also be connected with unbalanced sound sources. · If a mono sound source is connected to the L jack, the L input signal is sent to both channels 13 and 14. Connecting synthesizers, other sound sources and audio equipment (line level sound sources) Line level sound sources can be connected to every channel (1­16). However, the types of jacks and mixer functions differ depending on the channel. Channels 7­16 are five pairs of stereo channels, and channels 9-10 can also be connected to a record player. ª · On M-164FX and M-164UF mixers, if the INT. EFFECT RTN switch is not pushed in, the internal effects return signal is input to channels 13-14. CAUTION · On M-164FX and M-164UF mixers, when connecting an external sound source to the standard jacks of channels 13-14, push the INT. EFFECT RTN switch in to set channels 15-16 as the internal effects return channels. EFFECT RTN switch is not pushed in, the signal from the external sound source connected to the standard jacks of channels 13-14 and the internal effects return signal will interfere with each other and neither signal will be input correctly. The signals from channels 13-14 can also be sent to AUX 1. Channels 1­6 are balanced, but they can also be connected with unbalanced sound sources. The mixer channel functions include a high-pass filter, a 3-band EQ, AUX 1 and 2 sends and pan. · Connect using the standard (LINE) jacks. These jacks · Use the TRIM knobs on the top panel to adjust the input · ª Channels 7-8 R). These jacks are balanced, but they can also be connected with unbalanced sound sources. 1 and 2 sends and balance. · Connect a stereo sound source using standard jacks (L, ª Channels 15-16 on the top panel. This stereo mini-jack is convenient for connecting iPods and similar devices. · Connect a stereo sound source to the STEREO IN jack · If a mono sound source is connected to the L jack, the L · The mixer channel functions include a 2-band EQ, AUX ª CAUTION On M-164FX and M-164UF mixers, when a plug is connected to the STEREO IN jack, this external input is prioritized even if the INT. EFFECT RTN switch is pushed in, setting channels 15-16 as the internal effects return channels. As a result, the effects signal will not be returned to these channels. Therefore, when using this jack, set the internal effects return to channels 13-14. Channels 9-10 (L, R). · Connect a stereo sound source using RCA pin jack jacks · A record player can be connected to these jacks. When · On the M-164FX and M-164UF models, the signals from channels 15-16 can also be sent to AUX 1. doing so, press in the PHONO ON switch on the top panel. In addition, connect the grounding wire from the record player to the SIGNAL GND jack. 1 and 2 sends and balance. · The mixer channel functions include a 2-band EQ, AUX Setting the internal effects return channels (M-164FX and M-164UF) When using the internal effects of an M-164FX or M-164UF mixer, either channels 13-14 or 15-16 can be used as the return channels. When using the channel 13-14 input jacks on the rear panel, push the INT. When using the channel 16 TASCAM M-164/M-164FX/M-164UF 3 - Preparation for Use 15-16 STEREO IN jack on the top panel, select channels 13-14 as the return channels by setting the INT. EFFECT RTN switch so that it is not pushed in. Indicator STEREO IN jack When using channels 13-14 as the return channels, do not use the channel 13-14 input jacks on the rear panel. [. . . ] USB keyboards and mice are exceptions, however, and connecting them should not cause any problems. This shows the current status of the driver and connected hardware. Changes to various driver settings can be made here. · Settings section Driver settings Audio Performance (Windows OS) The M-164UF driver stores audio input and output signals temporarily in a buffer. The buffer can be set to one of five sizes using the Audio Performance item. The smallest buffer size has the lowest latency, while the largest buffer size has the highest latency. [. . . ]