User manual TASCAM KAMESAN KS-1017

[. . . ] The frame rate for the unit is shown on the front panel. 4 Kachinko System Parts of the KS-1018 The layout of the KS -1018 is quite straightforward, but here are some brief notes about the features and controls, which will help you when operating the unit. Front panel The front panel contains the following: Audio threshold (A1 and A2) controls and indicators PRESET/MANU selectors START switch Millisecond/frame and timeout indicators Data indicators Audio monitor switch Video probe connector NTSC PRE SET A U D I O 0 A1 10 0 A2 10 MONI A1 SPK A1 A2 O FF V 1st A2 DELAY TIME DATA 2nd 3rd KS-1017 LIP CHECKER DATA SEL. ) MANU V I D E O ms 0 TH. 10 - GAIN + 4-digit display Video level Video meter gain/threshold Data and indicator selection switch Millisecond/frame selector switch Power switch and indicator PRESET/MANU switches Only one of these switches can be on (lit) at one time. They determine whether the video threshold and gain controls will determine the threshold and gain of the signals (MANU) or whether the KS -1017's preset values will be used (PRESET). Typically, you can use the PRESET value whenever you use the KS -1018 "clapperboard", but you may need to use the MANU setting when you are using other synchronization sources. [. . . ] We suggest that you use the gain and threshold controls when you are using a synchronization signal other than the KS 1018, so that the "clapperboard" pushes the level to the third segment of the meter (the nominal trigger level). Data selection switch (DATA SEL. ) and data selection indicators Use this switch to rotate between up to three measurements (the time lag between the different signals). The green indicators below the audio/video data indicators show which measurement is currently selected, and the display shows the value of the delay of that measurement (or a timeout). 4-digit display This shows either the time in milliseconds or frames. If the delay is too long to be measured, the display shows all dashes, and the red T. OVER indicator lights. Millisecond/frame selector switch Use this to choose between displaying the delay in milliseconds or in frames, as shown by the indicators to the right of the display. The indicator lights red and flashes when the battery power is becoming low. POWER ON and battery indicator Turn unit on and off with 7 Kachinko System Rear panel AUDIO 2 JOINT CN MIC LINE MIC LINE AUDIO 1 There are two identical balanced female XLR-type connectors used for the input of audio signals to the KS -1018, marked AUDIO 1 and AUDIO 2. Each connector has a mic/line level switch (MIC/LINE), used to match the input level with the level of the audio sync signal. There is also a female 15-pin D-sub connector, allowing the connection of the two balanced audio signals as well as a power supply. See the specifications for details of how to wire this connector. Side view There is only one control on the left side (as you look from the front). Use a small Phillips screwdriver to adjust the volume (clockwise to increase the volume, counterclockwise to decrease it). About the case Thecarrying case for the KS1018 may hold a few surprises!The rear flap can be folded back for access to the XLR connectors for the analog inputs, as well as the MIC/LINE switches. 8 Kachinko System The KS -1017 must be removed from the case if the combined connector is to be used. The top flap covering the control panel and the video probe pocket can be folded back on itself, and used as a stand to prop the KS -1017 up at a convenient angle on a working surface. Note that you must disconnect the video probe before closing the flap. Batteries The KS -1017 uses 4 AA dry-cell or rechargeable batteries. These are located in the battery compartment accessed using the hinged cover at the top of the unit. Take care that the batteries are inserted correctly with the polarity correct. Never mix batteries of different types, or discarded (or partiallydischarged) and new (or freshly-charged) batteries. Always follow the battery manufacturer's instructions for charging rechargeable batteries. Never attempt to recharge batteries which are not designed for this purpose. 9 Kachinko System Using the KS-1018 with the KS-1017 This procedure should take place in the rehearsal stage of the broadcast. Connect the audio signals to signals split off from the main and sub feeds. Arrange for the remote source to turn on the light and sound using the MANU setting and the on/off button on the top of the KS-1018. START button You should hold the probe near the screen so that the vidDetect indicator eo should trigger (the indicator by the video TH. Note that the status of the DETECT indicator on the probe mirrors the status of this indicator. [. . . ] The threshold control is turned counterclockwise to make it more sensitive (that is, a lower light level will trigger the video detection and light the indicators on the main unit and the probe). 11 Kachinko System Interpreting the results 1. key to cycle through the three different readings (between 1st and 2nd, and 2nd and 3rd on the top row of the three selection indicators, and between 1st and 3rd on the bottom). The gap between the signals is shown in either milliseconds or in frames, depending on the setting made with the mS/FRAME switch. If an interval is too long to be displayed (over 6 seconds), the T. OVER indicator lights when the reading is selected and the display shows all dashes. [. . . ]