User manual TASCAM HS-8

[. . . ] D01106920A HS-8 8 Channel Audio Recorder OWNER'S MANUAL IMPORTANT SAFETY INSTRUCTIONS CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). The lightning flash with arrowhead symbol, within equilateral triangle, is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance. This appliance has a serial number located on the rear panel. Please record the model number and serial number and retain them for your records. [. . . ] INFO button: Touch to open a pop-up window that shows information about the currently selected folder. If no folder is selected, press this button to show information about the current project. MAKE FOLDER button: Touch to open the screen where you can create a new folder. MULTI SELECT button: Touch to enable the selection of multiple folders. MENU button: Touch to open a pop-up menu where you can select LOAD, REBUILD, EDIT TC and DELETE. Scroll buttons: Use these buttons to scroll to the beginning or end of the list or scroll one page (five lines) forward or backward. You can also scroll through the list one line at a time using the DATA dial. MENU button: Touch to open a pop-up menu where you can select LOAD, REBUILD, COPY, and DELETE. Scroll buttons: Use these buttons to scroll to the beginning or end of the folder list or scroll one page (five lines) forward or backward. You can also scroll through the list one line at a time using the DATA dial. Project name/folder name display at the top right of the screen: Touch to open a screen that shows the list of takes in the current project/folder. Take selection screen Folder selection screen Project operations Creating new projects 1 Press the PROJECT key on the front panel to open the PROJECT screen. 2 Touch the CREATE PROJECT button on the PROJECT screen to open the CREATE PROJECT screen. This screen has two pages. 34 TASCAM HS-8 5 ­ Projects 4 Touch the OK button when the confirmation pop-up message appears. CREATE PROJECT screen 1 You can make the following settings on this screen. Project Name: Touch the Project Name button to open the screen where you can edit the project name. Folder Name: Touch the Folder Name button to open a screen where you can change the name of the first folder. NOTE On the 1st FOLDER screens, the maximum number of characters allowed is indicated by the yellow background. When creation of the project completes, the Home Screen reopens. NOTE · · Immediately after creation, the new project becomes the current (loaded) project. The letter "C" appears on the icon to the left of the name of the current project on the PROJECT screen. Editing the project name 1 Touch the Project Name button on the CREATE PROJECT screen to open the PROJECT NAME screen as shown below. Fs: Set that sampling frequency of the project. 48k-0. 1% sampling frequency is pull-down compatible, and 48k+0. 1% is pull-up compatible. To use the actual sampling frequency of the recordings, select Actual Rate. For pull-up/ pull-down, select Fake Rate to write 48k instead of 48k±0. 1%. NEXT: Open the next page. Date button: Touch this button to change the project name to the date currently set for the unit in a "yyyy-mm-dd" format. NOTE · If the same project name or folder name already exists, an underscore ("_") followed by a number that has not been used is added. After pressing the "Date" button to change the name to the date, you can further edit the name on this screen. CREATE PROJECT screen 2 You can make the following settings on this screen. OTHERS: Use the Current Settings of other parameters to create a project or select Factory Preset to use the default settings. [. . . ] Mark Point set New Folder Name must not start with ""@"" No Call Point ssssssss = folder name You tried to skip marks before the Mark point was accorded. This disappears automatically after 2 seconds. The record function is not ON for any tracks. The maximum number of files and folders that can be created has been reached, so the operation could not be completed. The selected project/folder/take could not be *** = project, folder or take found, so the operation could not be completed. [. . . ]