User manual TASCAM DA-88 annexe 1

[. . . ] Press DISPLAY to exit Display will exit automatically SY SY SY SY Display Sub-Frame difference Auto Offset Calculate & Store Display Generator Start Time & Enter Data Column by column Generator or Offset time Setting and or or 7 8 9 10 11 12 13 14 15 16 Display MEMO 1 & Enter data Display MEMO 2 & Enter data Display OFFSET & Enter data Display OFFSET & Enter Data Display PITCH & Enter data Display Tape Time Code Display User Bits on tape Display Incoming Time Code Pull Up / Down mode setting Display Pull Up / Down Status SY DISPLAY DISPLAY DISPLAY DISPLAY DISPLAY or VARI or or or or or - SY SY SY SY SY Hold DISPLAY + Hold + DISPLAY Hold + Display Hold and press Fs Press Fs button - or - Page 1 © TEAC America, Inc. , 1997 All rights reserved. DA-88 quick ref. doc 10/14/97 7:27 PM Basic Functions cont. Software Version 4. 01 Items marked SY are only available when the SY-88 is installed. Function 17 18 19 20 Slave reference, Time Code or ABS time Digital or Analog output mode selection Track Delay ALL Track Delay Display LED ABS To Enter Function SY Press & Hold press Digital In Hold press DISPLAY Hold press DISPLAY then Hold Rec. for track 2 Hold press DISPLAY Hold press SHUTTLE Hold press CHASE Perform Rehearsal Perform Rehearsal Press & when Rehearsal or Auto In LED is blinking or On In TEST mode Hold + + DISPLAY + and press remote. Release & first then DISPLAY To Enter Data or - Remarks Press DISPLAY to exit This sets a 43Fs delay on all 8 tracks for digital dubbing. [. . . ] The Bernoulli ef fect explains how a spinning drum creates a cushion of air between the tape and the heads. S-Err-03 Combination of Errors 1 & 2 S-Err-04 Capstan Motor Problem. The motor spin command is given, but no FG signal is detected within 1. 5 seconds. S-Err-05 Combination of Errors 1 & 4 S-Err-06 Combination of Errors 2 & 4 S-Err-07 Combination of Errors 1, 2 &4 S-Err-08 Reel Problem (take-up or supply). S-Err-09 Combination of Errors 1 & 8 S-Err-10 Combination of Errors 2 & 8 S-Err-11 Combination of Errors 1, 2 & 8 (a mechanical mode change is not completed within 5 seconds). S-Err-12 Combination of Errors 4 & 8 S-Err-13 Combination of Errors 1, 4 & 8 S-Err-14 Combination of Errors 2, 4 & 8 S-Err-15 Combination of Errors 1, 2, 4 & 8 S-Err-21 The reel tables do not wind the tape in preparation for Eject. If the tape path has been adjusted for a narrow or easily flexed tape, a wider or stiffer tape may get caught in the guides. The System control monitors both reel table tachometers, as well as the Head and Capstan tachs. S-Err-59 In Eject mode, the reels do not start to drive, or do not lock for more than 1. 5 seconds S-Err-68 In Play mode, the reels do not start to drive, or do not lock for more than 1. 5 seconds. E. CLOC No clock data, or incorrect setting of the clock switch or machine time base reference. This could also indicate a mismatch in the machine ID K numbers and/or missing sync signal such as video or word clock. You must use TASCAM cables or other individually shielded twisted pair cable. Leave the machine powered so the heat from the electronics will evaporate the moisture. You must use either a metal particle (MP) or metal evaporated (ME) HI-8 Tape. [. . . ] 3) Power On both DA-88s 4) On the Source DA-88, enter a 43 Fs Track Delay value for all 8 tracks. c) If dubbing Time code, on Source DA-88 set menu Item 6 to Digital (old S1 #5 Up). 5) Load Master tape into Source DA-88 and the pre-formatted tape into the target DA-88. [. . . ]