User manual TASCAM CD-VT2

[. . . ] » CD-VT2 Portable CD Music & Voice Trainer D00997320A This device has a serial number on the rear panel. Serial number: __________________ OWNER'S MANUAL IMPORTANT SAFETY INSTRUCTIONS FOR U. S. A. TO THE USER This equipment has Using mics with the trainer tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. [. . . ] Do not use any other adapter because this may cause the player to malfunction. Connect the DC plug from the AC adapter to the DC IN 5V jack on this device and connect the AC plug to a standard outlet. 1 TASCAM CD-VT2 The remaining power level of the batteries is low. The batteries are out of power and the unit power is about to turn OFF. Put in new batteries. About Power IMPORTANT SAFETY PRECAUTIONS TASCAM AC outlet PS-P520 sold separately) Startup completes in a few seconds and the TIME DISPLAY screen appears. To turn the power OFF, press and hold the POWER switch on the rear of the unit for more than one second. Release the button when the screen below appears on the display. DC PLUG When using the AC adapter, " " appears in the upper right of the display. NOTE Unplug the AC adapter when not using the unit. NOTE Always use the POWER switch to turn the power ON and OFF. When the unit is operating, if you disconnect the power adapter or remove the batteries to turn the power OFF, your settings may not be saved. All the settings might even be initialized, reverting them to their default values. When using this player with batteries, the power turns OFF temporarily if you remove or connect the AC adapter. Turning the power ON and OFF Press and hold the POWER switch on the rear of the unit for about one second to turn its power ON. Release the button when the screen below appears on the display. 1 TASCAM CD-VT2 IMPORTANT and functions of parts Names SAFETY INSTRUCTIONS Control panel 2 TEMPO key Press this key to open the TEMPO CHANGE screen. You can change the playback tempo and turn the VSA function ON and OFF on this screen. (See "Changing the tempo" and "Changing the pitch with the tempo" on page 26. ) 3 KEY key Press this key to open the KEY & PITCH screen. (See "Changing only the pitch" on page 26. ) 4 VOCAL CANCEL key Press this key to open the VOCAL CANCEL screen where you can change the VOCAL CANCEL function settings. (See "Reducing the sound of recorded vocals and solo instruments" on page 27. ) 5 EFFECT key Press this key to open the EFFECTOR screen. (See "Using built-in effects" on page 31. ) 6 TIME DISPLAY key Press this to open the TIME DISPLAY screen, which shows the status of the CD during playback and other information. (See "TIME DISPLAY screen" on page 21. ) 7 LOOP key Turns the loop playback and repeat playback functions ON and OFF. When IN and OUT points are set, this key turns 1 TASCAM CD-VT2 1 Display Shows CD status during playback, device settings and other information. IMPORTANT functions of parts Names and SAFETY PRECAUTIONS loop playback ON and OFF. (See "Loop playback" on page 28 and "Repeat playback" on page 29. ) 8 IN/OUT key Use this key to set the loop playback IN and OUT points. Set and use the metronome and make various device settings on this screen. (See "Using the tuner" on page 34. ) q LEVEL key Press this key to open the LEVEL screen. Make independent adjustments to the MIC 1 and MIC 2 input and CD playback volumes on this screen to change the mix balance as you like. (See "Using mics with the trainer" on page 30. ) w CURSOR (§, ¶, , ¥) keys Select among setting items on the screen with these keys. [. . . ] NOTE TEMPO and BEAT settings are save when the power is turned OFF and will be the same the next time that you use the metronome. If you press the CURSOR ¶ key when the BEAT item is selected, the MONO MONITOR item is selected and the metronome settings window disappears. Press the CURSOR § key to return to the metronome settings. UsetheVALUE (+)keytoturnitON. Themetronome startswiththetempoandbeatsettingslastused(or thedefaultsettingsifthisisthefirsttimeused). WhenthemetronomeisON, itsTEMPOandBEAT settingsappear. UsetheCURSOR(§, ¶)keystoselect theitems, andtheVALUE(+, ­)keystochangetheir settings. 4 TASCAM CD-VT2 IMPORTANT SAFETY PRECAUTIONS Other functions Stopping the metronome Do one of the following: · Press the STOP key. [. . . ]