User manual TASCAM CD-RW901 annexe 1

[. . . ] » CD-RW901 CD Rewritable Recorder Professional OWNER'S MANUAL D00910920A 1 - Introduction IMPORTANT SAFETY PRECAUTIONS CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). The lightning flash with arrowhead symbol, within equilateral triangle, is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance. This appliance has a serial number located on the rear panel. Please record the model number and serial number and retain them for your records. [. . . ] Whenstopped, setthemodetodisplayContinueor Mode>Cont. TASCAM CD-RW901 2. PressthePLAYkeytobeginplaybackinorderof thetracknumber. 19 4 - Playback operations Single-track playback This function enables playback of just a single track. Whenstopped, setthemodetodisplaySingleor Mode>Single. TheMULTI JOGdialcanbeusedtoselectthe trackalso. UsetheSKIPkeysorthenumberkeys(0~9)on theremotecontroltoselectthedesiredtrack. Random playback In this mode, the unit will play back all the tracks on the disc in completely random order, regardless of track number. Press the PLAY key and random playback will begin. NOTE Even when the power is turned off, the unit will remain in Random mode. Program playback This function enables playback of selected tracks in any desired order. Whenprogramsettingiscompleted, pressthe PLAYkeytobeginplaybackofthetracksinthe programmedorder. NOTE 2. Usethenumberkeys(0~9)ontheremotecontrol unittoselecteachdesiredtrackforprogram playback, thenpresstheENTERkey. YoucanalsorotatetheMULTI JOGdialtoselect thetracknumberandpushtoenter. Thetracknumberwillbeenteredintotheprogram. Repeat the above step 2 until the desired program is completed. As the program is being created, the program number and total program playing time is revised on the display. NOTE If the STOP key is pressed without first pressing the PLAY key, all the program data will be erased. When stoppped, if the playback mode is switched to another, all the program data will be erased. In this mode, if there are no tracks programed, the CD-RW901 will not start playback. If an attempt is made to enter more than 100 program steps, the message PGM Full!If the total program playing time exceeds 999 min 9 sec, --- : -- appears on the display. If the CLEAR key is pressed, the programmed track will be deleted from the last. Time display switching When the TIME key on the front panel or the remote control is pressed, the time display will switch through several modes on the display. · Elapsed track time (no display light indication) · Remaining track time (REMAIN is lit in the display) · Elapsed disc time (TOTAL is lit in the display) · Remaining disc time (TOTAL and REMAIN are lit in the display) NOTE In program mode, pressing the TIME key displays the elapsed and the remaining time of the whole program. When playing an MP disc, elapsed track time is always displayed, and the TIME key cannot be used. For details on time display during recording, please refer to "Time display while recording" in "Recording" section on page . Even when power is turned off, the time display mode setting is retained. When stopped, the total recording time is shown, regardlessofthestatusoftheTOTALandREMAINindicators. 0 TASCAM CD-RW901 4 - Playback operations EXT SYNC playback In this mode, the unit will play back in synchronization with the clock selected as digital input source (OPTICAL, COAXIAL, AES/EBU). When stopped, use the EXT SYNC option in the PLAY sub-menu (see "Operation basics" on page 16) to set the external synch playback mode on. Select the input source for sync playback. NOTE If the selected digital input source is at 48kHz, using the 48k Fs adjustment function allows the audio to be played back at the correct pitch. When stopped, and when in playback or playback ready mode, press the SYNC REC key to turn the 48k Fs adjustment function on or off. The setting remains until the EXT SYNC function is set to off, and even the power is turned off. NOTE When the EXT SYNC is on, and when the unit detects a signal other than . 1kHz, synchronization with the clock of the selected digital input source may fail, and EXT CLK Err! [. . . ] RotatetheMULTI JOGdialorrepeatedlypress theMENU (+/-)keysontheremotecontrolto selectthetracknumberyouwishtotitle. TASCAM CD-RW901 7 - Titling Using a keyboard with the CD-RW901 A computer keyboard can be connected to the IBM PC compatible PS/2 interface on the front panel to operate certain functions of the CD-RW901. It is particularly efficient for title input. Keyboard type setting The CD-RW901 must be set for the type of keyboard being connected. Set the type using the sub-menu KEYBOARD option on the SYSTEM sub-menu. [. . . ]