User manual TASCAM CD-RW2000

[. . . ] » CD Rewritable Recorder Professional 3D0038800A CD-RW2000 OWNER'S MANUAL Ü ÿ Y This appliance has a serial number located on the rear panel. Please record the model number and serial number and retain them for your records. Model number Serial number CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. [. . . ] It should also be noted that this call function is available in play and pause modes only. Note that the call mode is not available when shuffle mode has been selected (see 3. 1. 3, "Playback modes") and there is no "call point" set. tion of the track as indicated by the subcode, but at the first position of the track where the audio level exceeds a set trigger level. The trigger level is the same as the recording trigger level, as set in 4. 3. 1, "Synchronized recording". To set the Auto Cue function on: 1 Repeatedly press the MENU key (9 or 6) until the display shows A_CUE > XXX where XXX is either ON or OFF. 2 Use the MULTI DIAL control B or the SKIP keys H to set the function to ON. When the function is on, the A-CUE display indicator is lit. NOTE 3. 5 Auto Ready function This function allows the playing back of a single track, and the automatic cueing of the next track ready for playback. The unit is cued to the start of the track as determined by the subcode, not the start of the audio signal, unless the AUTO CUE function is on (see 3. 6, "Auto Cue function"). The unit will enter pause mode in the continue, shuffle and programmed play modes, after the location has taken place. If repeat is active (see 3. 3, "Repeat play"), the unit will enter play ready mode at the start of the next track (REPEAT ALL), or the start of the track which is being repeated (REPEAT 1). To set the function: 1 Repeatedly press the MENU key (9 or 6) until the display shows A_READY>XXX where XXX is either ON or OFF. 2 Use the MULTI DIAL control B or the SKIP keys H to set the function to ON. When the function is on, the A-READY display indicator is lit. When using the Auto Cue function, there may be a short "click" sound output through the DIGITAL COAXIAL and OPTICAL OUT terminals (X and Y) as the unit locates to the audible start of the track just before it enters pause mode. However, this sound will not be output through the DIGITAL AES/EBU OUT terminal W. 3. 7 Incremental play Incremental playback means that when the STOP key G or I is pressed (or if a STOP signal is received through the CONTROL connector T) while a track is being played back, the playback position will be at the start of the next track. If the PLAY key H is pressed while the incremental playback mode is on, playback starts from the start of the next track. To set the incremental play mode on: 1 Repeatedly press the MENU key (9 or 6) until the display shows INC PLAY>XXX where XXX is either ON or OFF. 2 Use the MULTI DIAL control B or the SKIP keys H to set the function to ON. Although there is no indication when the incremental play mode is selected, you will notice that is in operation whenever you stop playback of a track. 3. 6 Auto Cue function The Auto Cue function allows you to set up the unit so that when a track is selected for playback in pause mode (cued), playback will start, not at the first posi- TASCAM CD-RW2000 17 4 ­ Recording Before you start recording using the CD-RW2000, make sure that you understand the following key points: · Once you have recorded on a CD-R disc, the data cannot be erased from it. Once finalized, a CD-R disc is "fixed" and behaves in the same way as a pre-recorded disc. Finalized CD-RW discs, however, can be erased, refreshed and re-recorded. There is also a ---- setting which represents a complete signal cut. NOTE If digital direct is selected, as described below (4. 3. 3, "Digital direct"), the digital volume is bypassed and this menu item disappears. However, once the digital direct mode is turned off, the menu reappears, the settings previously made here will take effect, and the input volume may suddenly change. 4. 1. 2 Input monitoring 4. 1 Input selection To select the input to be recorded, press the INPUT SELECT key on the main unit 6. [. . . ] 6 At the end of the countdown period, the word Complete appears briefly on the display, and the display returns to the track/time display (of course, there are no tracks, and the disc is as the start, with the total time of the disc available for recording). 7. TASCAM CD-RW2000 29 6 ­ Reference and specifications 6. 1 Troubleshooting Symptom No sound on playback (the disc is playing and the time display is incrementing) No meter indication when a source is input D-IN UNLOCK! Symptom Rec Error Possible cause and remedy General recording error. This may be caused by vibration or a shock during recording, for example, or may be the result of a bad disc. The OPC area is full, and no further recording is possible on this disc. Seen when a CD-RW disc OPC area is full, and the CD-RW2000 automatically cleans up the OPC area for further recording. [. . . ]