User manual TASCAM CD-GT2

[. . . ] » CD-GT2 Portable CD Guitar Trainer D00996120A This device has a serial number on the rear panel. Serial number: __________________ OWNER'S MANUAL IMPORTANT SAFETY INSTRUCTIONS FOR U. S. A. TO THE USER This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful inter ference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. [. . . ] (See "Changing only the pitch" on page 26. ) 4 GUITAR CANCEL key Press this key to open the GUITAR CANCEL screen. Turn the guitar cancel function ON and OFF and change its settings on this screen. (See "Reducing the sound of recorded guitars" on page 26. ) 5 EFFECT key Press this key to open the EFFECTOR screen. (See "Using built-in effects" on page 30. ) 6 TIME DISPLAY key Press this key to open the TIME DISPLAY screen, which shows the status of the CD during playback and other information. (See "TIME DISPLAY screen" on page 21. ) 7 LOOP key Turns the loop playback and repeat playback functions ON 1 TASCAM CD-GT2 1 Display Shows CD status during playback, device settings and other information. IMPORTANT functions of parts Names and SAFETY PRECAUTIONS and OFF. When IN and OUT points are set, this key turns loop playback ON and OFF. (See "Loop playback" on page 27 and "Repeat playback" on page 28. ) 8 IN/OUT key Use this key to set the loop playback IN and OUT points. Set and use the metronome and make various device settings on this screen. (See "Using the tuner" on page 33. ) q LEVEL key Press this key to open the LEVEL screen. Select whether to use the GUITAR/MIC IN jack for guitar input or mic input and make independent adjustments for the input signal and CD playback volumes on this screen. (See "Using guitars and mics" on page 29. ) w CURSOR (§, ¶, , ¥) keys Select among setting items on the screen with these keys. e VALUE (+, ­) keys Change the value of the item selected on the screen. 1 TASCAM CD-GT2 r PHONES VOLUME (+, ­) keys Adjust the volume sent to your headphones using these keys. Press and hold this key to fast forward through a track that is playing or paused. Press and hold this key when the CD is stopped to automatically skip forward (increment) though the tracks. Press and hold this key to fast reverse through a track that is playing or paused. Press and hold this key when the CD is stopped to automatically skip backward (decrement) though the tracks. o FLASH BACK key Press during playback to jump to a point in the track a few seconds earlier and continue playback. (See "Jumping back a few seconds (FLASH BACK)" on page 24. ) IMPORTANT and functions of parts Names SAFETY INSTRUCTIONS Front f GUITAR/MIC IN jack (standard phone jack) Connect an electric guitar or microphone. g FOOT SW jack (standard phone jack) Connect a TASCAM RC-30P or other momentary footswitch (non-latching). screen. p OPEN switch Slide this switch away from the PHONES jack to open the control panel and insert and remove discs. a PHONES jack (stereo minijack) Connect headphones to this jack to output the CD playback signal and the input signal from the GUITAR/MIC IN jack. s LINE OUT jack (stereo minijack) Outputs the CD playback signal and input signal from the GUITAR/MIC IN jack. [. . . ] screen and make settings as necessary. Setting the polarity When using a footswitch other than a TASCAM RC-30P, the polarity might need to be changed. Use the CURSOR (§, ¶) keys to select the FOOT TYPE item and the VALUE (+, ­) keys to select NORMAL or INVERT according to the type of footswitch used. Setting the function Use the CURSOR (§, ¶) keys to select FOOT FUNC, and the VALUE (+, ­) keys to choose one of the following functions. TASCAM CD-GT2 IMPORTANT SAFETY PRECAUTIONS Making various settings You can change various settings to optimize the device for your use environment and other requirements. Use the CURSOR (§, ¶) keys to select the desired item and the VALUE (+, ­) keys to set the value. Select one of the following MONO OFF L+R L R MONITOR settings. ordinary stereo monitoring (default setting) both channel signals are mixed and output in mono left channel signal is output on both channels right channel signal is output on both channels Splitting the CD and guitar sounds Mono monitoring You can output a mono signal from the PHONES and LINE OUT jacks. [. . . ]