User manual TASCAM CD-A700

[. . . ] REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. ESPAÑOL OWNER'S MANUAL / MANUEL DU PROPRIETAIRE BEDIENUNGSANLEITUNG / MANUALE DI ISTRUZIONI MANUAL DEL USUARIO / GEBRUIKSAANWIJZING ITALIANO DEUTSCH FRANÇAIS ENGLISH IMPORTANT SAFETY INSTRUCTIONS CAUTION: O Read all of these Instructions. 1) Read Instructions -- All the safety and operating instructions should be read before the product is operated. 2) Retain Instructions -- The safety and operating instructions should be retained for future reference. 3) Heed Warnings -- All warnings on the product and in the operating instructions should be adhered to. [. . . ] If higher track numbers are entered in the Program memory, the OVER indicator will light. 3. Alternately press the Ú SKIP Æ button(s) and the PROGRAM button in the following order. (select 5) (enter) (select 2) (enter) (select 8) (enter) 4. Programmed playback starts from the first programmed tune. To cancel a programmed track Pressing the CLEAR button will cancel the last programmed track. O Programming tunes is possible only when the player is in the Stop mode. O The programmed contents will be held in memory even after programmed playback has been completed or when programmed playback is stopped by pressing the STOP button. O When the STOP button is pressed in the stop mode, the contents of the program are erased. O During program playback, the TOTAL REMAIN time display shows the total remaining time of the programmed tunes, from the current position. O If tunes with numbers higher than 32 are programmed, TOTAL time may not appear in the display. ("nn:nn" appears in the display. ) _8_ RANDOM Playback 1. The SHUFFLE indicator lights in the display. Repeat Function The repeat function allows repeat playback of any single tune, the entire disc, or any desired portion on the disc designated by two (start and end) points. O The repeat functions can be released by pressing the repeat button again. To repeat a designated section (A-B Repeat mode) 1. Designate the point at which repeat playback should start (point A) by pressing the A-B button. 2 Elapsed time display When playback begins, the elapsed time of the tune being played is displayed in minutes and seconds. 3 Remaining time display (REMAIN) Displayed when the TIME button is pressed once. This provides an easy check of the remaining time of the tune being played. 4 Total remaining time display (TOTAL REMAIN) Displayed when the TIME button is pressed twice. The time displayed is the total remaining playback time from the position being played, to the end of the disc; the counter counts down to "00:00" during playback. Intro Check Function The intro check function allows only the beginning of each track to be played for 10 seconds. O The intro check function also works together with SHUFFLE, PROGRAM and REPEAT ALL functions. O Displayed after the TIME button is pressed three times. O In Normal Playback mode, if a tune with a number higher than 32 is being played, the remaining time will not be displayed in the time counter even when the TIME button is pressed. Instead, "nn:nn" will be indicated on the time indicator. _ 10 _ Cassette Deck Operation Playback 1. Set the REV MODE switch to the required tape travel mode. INPUT COUNTER RESET STOP RECORD 3. Load a pre-recorded cassette with its open edge facing down and side A facing toward you. O To stop playback, press the STOP button. POWER SOURCE REV MODE DOLBY NR EJECT Recording 1. [. . . ] * Both are available in TEAC Tape Cleaning Kits HC-2 and RC-2 in the U. S. A. or TZ-261 in other areas. Erase Head Record/Play Head Demagnetizing heads Be sure that the power is off, then demagnetize the heads using a TEAC E-3 demagnetizer. For details of its use, read its instructions. DO NOT cut off the mains plug from this equipment. If the plug fitted is not suitable for the power points in your home or the cable is too short to reach a power point, then obtain an appropriate safety approved extension lead or consult your dealer. [. . . ]