User manual TASCAM CD-355

[. . . ] » CD-355 Compact Disc Changer OWNER'S MANUAL D00989320A IMPORTANT SAFETY PRECAUTIONS CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). The lightning flash with arrowhead symbol, within equilateral triangle, is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance. This appliance has a se rial numbe r located on the rear panel. Please record the model number and serial number and retain them for your records. [. . . ] Since some of these discs do not complywiththeCDspecifications, theymaynotbeplayable ontheCD-355. (Compactdiscscanbeplayedorrecordedonlyononeside. ) < To remove a disc from its storage case, press down on the centerofthecaseandliftthediscout, holdingitcarefullyby theedges. < IfyouareinanydoubtastothecareandhandlingofaCD-R/ CD-RW disc, read the precautions supplied with the disc, or contactthediscmanufacturerdirectly. Howtoremovethedisc Howtoholdthedisc MP3 files < ThisunitcanplayMP3filesrecordedonaCD-RorCD-RW. This unit cannot display symbols and full-size or double-byte characters(suchasJapanese, Chinese, etc. )correctly. Also, be suretousethefileextension. (". mp3") < MP3 files are monaural or stereo MPEG-1 Audio Layer 3 format. This unit can play MP3 files with sampling frequency 44. 1kHzor48kHz, bit-rate320kbpsorless. < Whenmorethan512files(includingfolders)arerecordedon thedisc, theunitmightnotbeabletoplayitcorrectly. Conversely, the other appliances may operateincorrectly. Usethesebuttonstoselectatracknumber. Forinstance, toselecttracknumber35, press"3"and"5". M PROGRAM Use this button to enter the program mode. In program mode, usethisbuttontoenterselections. N SEARCH (m/, ) During playback, use these buttons to search the part you wanttolistento. O SHUFFLE Usethisbuttonforshuffleplayback. P TIME Battery Installation Duringplayback, usethisbuttontochangethetimedisplay. Q REPEAT Usethisbuttontoselectrepeatmodes. R INTRO CHECK Usethisbuttontostarttheintrocheckplaying. S PROGRAM CHECK 1. Removethebatterycompartmentcover. Make sure that the batteries areinsertedwiththeirpositive"+"andnegative"_"poles positionedcorrectly. 3. Closethecover. Usethisbuttontocheckprogramedcontents. T CLEAR Usethisbuttontoclearaprogram. U SKIP (. //) Usethesebuttonstoskiptracks. Battery Replacement Ifthedistancerequiredbetweentheremotecontrolunitand mainunitdecreases, thebatteriesareexhausted. Inthiscase replacethebatterieswithnewones. Precautions concerning batteries < Be sure to insert the batteries with correct positive "+" and negative"_"polarities. < When the remote control unit is not to be used for a long time (more than a month), remove the batteries from the remotecontrolunittopreventthemfromleaking. Iftheyleak, wipe away the liquid inside the battery compartment and replacethebatterieswithnewones. < Donotheatordisassemblebatteriesandneverdisposeofold batteriesbythrowingtheminafire. TASCAM CD-355 Connection C A B D L R BALANCED OPTICAL COAXIAL LR UNBALANCED ANALOG IN DIGITAL IN ANALOG IN Audio device (CD Recorder, Amplifier, etc. ) CAUTION: <Switch off the power to all equipment before making connections. To prevent hum and noise, avoid bundling the signal interconnection cables togetherwiththeACpowercordorspeakercables. B LINE OUT jack Analog 2-channel audio signal is output from this jack. Makesuretoconnect:RCA whiteplugqwhitejack(L:leftchannel) redplugqredjack(R:rightchannel) A DIGITAL OUT terminal Connect the digital output terminal to the digital input terminalofadigitaldevicesuchasaCDrecorder, MDdeck, etc. <Keep the supplied cap to cover the optical digital terminal whenitisnotinuse. C ANALOG OUT (BALANCED) (L, R) TheseXLRconnectorsoutputanalogaudiosignalsat+4dBu tosuitably-equippedunits. Makesuretoconnect:XLR 1=GND, 2=HOT, 3=COLD D AC Power Cord After all other connections are complete, connect the plug totheACwallsocket. Be sure to connect the power cord to an AC outlet which suppliesthecorrectvoltage. Grasptheplug, notthecordwhenpluggingorunplugging thepowercord. 10 TASCAM CD-355 Playback 1 4 2 4 Press the OPEN/CLOSE button (L) to close the tray. 1 3 DISC NO. 5 5 Press the PLAY button (y) to start playback. 1 Press the POWER button to turn the unit on. Theunitstartssearchingdisc. Ifadiscisfoundtheplaybackwillstart. 2 Press the OPEN/CLOSE button (L). < Ifyouwanttoselectotherdisc, presstheDISCSKIPbuttonor thedesiredDISCNO. button. (AudioCD) discnumberanddiscmark musiccalendar 3 Place a disc on a tray with the printed label face up. tracknumber currentdiscnumber elapsedtimeofthecurrenttrack tray (MP3disc) discnumberanddiscmark carousel discnumber < Neverplacemorethanadisconatray. < Thediscmustbeloadedcentrallyintothedisctray. Ifthedisc is not correctly loaded, it may not be possible to open the trayagainonceithasclosed, soyoushouldensurethediscis alwayscentrallyloadedinthetray. < Donotforceopenorclosethetray. filenumber elapsedtimeofcurrentfile < Allthebuttonsandswitchesstillfunctionnormallyevenwhen thetrayisopeningorclosing. < Whentheunitdetectsadisconthetray, thediscmark" " willlight. [. . . ] < When in the program mode, the following buttons don't work: SHUFFLE, DISCNO. , DISCSKIP To check the programed order track/filenumber discnumber programnumber You can also use the SKIP buttons (. //) to select a track. < Iftheunithasnotyetdetectedthecontentsofthedisc, you can not enter 3-digit numbers with the numeric buttons. < Youcannotalsoenternumbersotherthanthosedetectedas specifyingtracks/filesinthedisc. In the stop mode, press the PROGRAM CHECK button repeatedly. Thetrackandprogramnumberswillbeshownon thedisplay. 1 TASCAM CD-355 Intro Check To add a track/file to the program If you want to add a track/file to the end of the program, press the PROGRAM CHECK button repeatedly until "A" appearsaftertheendoftheprogram. Then select a track/file number using the numeric buttons andpressthePROGRAMbutton. Thetrack/fileisaddedtothe program. [. . . ]