User manual TASCAM CC-222SLMKII

[. . . ] » CD Recorder/Cassette Deck D01022120A CC-222SL@# Professional OWNER'S MANUAL IMPORTANT SAFETY PRECAUTIONS 1 ­ Introduction CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). The lightning flash with arrowhead symbol, within equilateral triangle, is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance. This appliance has a serial number located on the rear panel. Please record the model number and serial number and retain them for your records. [. . . ] The selected mode is shown in large characters dis-appears from the display a few seconds after selecting the mode, and the display returns to its previous mode. · Continue. Playback continues in the normal order. Random playback In this mode, the unit will playback all the tracks on the disc in random order. Whileplayingback, usingthetrackskipfunction willmoveforwardsthroughtherandomorder. TurntheMULTI DIALontheunitclockwiseorpress the SKIP(¯)keyontheremotecontrol. NOTE You cannot go backwards to previous tracks in the Random playback mode. To stop random playback, press the STOP key. Ejecting the disc using the EJECT key also stops random playback. Program playback The steps to set up to 99 program steps (tracks) to be played back in a specified order are as follows: 1 Whenstopped, pressthePLAY MODEkeyuntilthe displayshowsProgram . 2 Thedisplaychangestoshow0T 00: r 00 00 , meaningthattherearenotracksassignedforprogramplayback. Thedisplayshowsthetrack, thecurrenttimedisplay, andtheprogramstepnumber. Whileinprogramplaybackmode, usingtheSKIP keysortheMULTI DIALmovesbackwardsandforwardsintheordersetintheprogram. 3 Usethenumberkeysontheremotecontroltoenter atracknumber. ThereisnoneedtopresstheENTER key. Thetrackenteredisassignedtotheprogramstep, andthedisplaychanges, showingthetracknumber, thetotaltimeoftheprogramsofar, andthestep number, e. g. 2T 1 : r 4 56 03 . Use the PAUSE key to stop playback temporarily or the STOP key to stop playback of the program. If the STOP key is used, when playback is restarted, it starts from the first program step. When stopped, if the CLEAR key on the remote control is pressed, it cancels the last track entered in the program. Clear the program by pressing the PLAY MODE until the display shows Cont nue The program is also cleared i . when the disc is ejected, and if the STOP key is pressed when playback is stopped in programmed order mode. The programmed play order is not memorized when the power is turned off. ul 4 Thenextprogramstepcanthenbeentered. NOTE Steps 3 and 4 above can also be carried out from the main unit by turning and pushing the MULTI DIAL key. 5 Repeatsteps3and4aboveuntiltheprogramis complete. 6 PressthePLAYkeytostartplaybackatthefirst programstep. If the total time programmed goes over 100 minutes, the message -- -- appears on the display. : TASCAM CC-222SLMKII 17 4 Disc operations 1 ­ Introduction Repeat playback The unit can repeat the whole of the disc, the current track only, or an A­B portion set as described here. Selecting the repeat mode is only possible using the remote control unit. NOTE To cancel repeat mode, press the REPEAT key again so that the display shows Repeat OFF and the RePeAT indicator goes out. You can use this mode with Single, Random, or Program playback modes. 1 Theunitshouldbeinplayback, standbyorstopmode. PresstheREPEATkeysothatthedisplayshows Repeat ON(theRePeATindicatorlights). A to B repeat playback You can set the points between which playback should loop. 1 Whileplayingback, presstheA-Bkeyontheremotecontrolatthepointwheretheloopistostart (A-point). The RePeAT indicatorlightsupandA-bindicatorblinks tillthesecondpoint(B-point)isentered. 2 PresstheA-Bkeyagainatthepointwheretheloop istoend(B-point). NOTE Cancel the A-B repeat mode by pressing the A-B key, or the STOP key. [. . . ] The STOPkeyistheonlykeywhichisenabledduringphonorecording. NOTE 3 PressthePHONOkey. ThePhONOindicatorlightson thedisplay. Ifthetapeiscurrentlyinstopmode, thetaperewinds, andthedeckentersrecordstandbymode (abouteightsecondsfromthestartofthecassette, toallowforleadertape). Ifthetapedeckisalreadyinrecordstandbymode, itwillremaininrecordstandbymode. It is not possible to perform phono recording as described above under the following circumstances: a tape is not loaded or the tape is write-protected (the phono to tape function is disabled with no recordable tape inserted), or the tape is not either stopped or in record standby mode. Only recording as described above is possible from the RIAA PHONO sources to tape. [. . . ]