User manual TASCAM CC-222SL

[. . . ] » CC-222SL CD Recorder/Cassette Deck D00964320A Professional OWNER'S MANUAL IMPORTANT SAFETY PRECAUTIONS 1- Introduction CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). The lightning flash with arrowhead symbol, within equilateral triangle, is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance. This appliance has a serial number located on the rear panel. Please record the model number and serial number and retain them for your records. [. . . ] The selected mode is shown in large characters dis-appears from the display a few seconds after selecting the mode, and the display returns to its previous mode. Selecting the playback mode is only possible using the remote control unit. 1 Whenstopped, pressthePLAY MODEkeyonthe remotecontrolrepeatedlytocyclethedisplay throughthefollowing: ·Continue. Playback continues in the normal order. Random playback In this mode, the unit will playback all the tracks on the disc in random order. Whileplayingback, usingthetrackskipfunction willmoveforwardsthroughtherandomorder. TurntheMULTI DIALontheunitclockwiseorpress theSKIP(¯)keyontheremotecontrol. NOTE You cannot go backwards to previous tracks in the Random playback mode. To stop random playback, press the STOP key. Ejecting the disc using the EJECT key also stops random playback. Program playback The steps to set up to 99 program steps (tracks) to be played back in a specified order are as follows: 1 Whenstopped, pressthePLAY MODEkeyuntilthe displayshowsProgram . 2 Thedisplaychangestoshow0T 00: 00 r 00 , meaningthattherearenotracksassignedforprogramplayback. Thedisplayshowsthetrack, thecurrenttimedisplay, andtheprogramstepnumber. Whileinprogramplaybackmode, usingtheSKIP keysortheMULTI DIALmovesbackwardsandforwardsintheordersetintheprogram. 3 Usethenumberkeysontheremotecontroltoenter atracknumber. ThereisnoneedtopresstheENTER key. Thetrackenteredisassignedtotheprogramstep, andthedisplaychanges, showingthetracknumber, thetotaltimeoftheprogramsofar, andthestep number, e. g. 2T 1 : r 4 56 . 03 Use the PAUSE key to stop playback temporarily or the STOP key to stop playback of the program. If the STOP key is used, when playback is restarted, it starts from the first program step. When stopped, if the CLEAR key on the remote control is pressed, it cancels the last track entered in the program. Clear the program by pressing the PLAY MODE until the display shows Cont nue The program is also cleared i . when the disc is ejected, and if the STOP key is pressed when playback is stopped in programmed order mode. The programmed play order is not memorized when the power is turned off. u l If the total time programmed goes over 100 minutes, the message -- -- appears on the display. : 4 Thenextprogramstepcanthenbeentered. NOTE Steps 3 and 4 above can also be carried out from the main unit by turning and pushing the MULTI DIAL key. 5 Repeatsteps3and4aboveuntiltheprogramis complete. 6 PressthePLAYkeytostartplaybackatthefirst programstep. TASCAM CC-222SL 1 4 Disc operations 1-­Introduction Repeat playback The unit can repeat the whole of the disc, the current track only, or an A­B portion set as described here. Selecting the repeat mode is only possible using the remote control unit. NOTE To cancel repeat mode, press the REPEAT key again so that the display shows RepeatOFF and the RePeAT indicator goes out. You can use this mode with Single, Random, or Program playback modes. 1 Theunitshouldbeinplayback, standbyorstopmode. PresstheREPEATkeysothatthedisplayshows RepeatON(theRePeATindicatorlights). A to B repeat playback You can set the points between which playback should loop. 1 Whileplayingback, presstheA-Bkeyontheremotecontrolatthepointwheretheloopistostart (A-point). TheRePeAT indicatorlightsupandA-bindicator blinkstillthesecondpoint(B-point)isentered. [. . . ] The deck enters record standby mode when the key is released. Erasing tapes Anything previously recorded on the tape will automatically be erased when you make a new recording on it. It can also be erased by "recording" on it with the INPUT level control set to "0". TASCAM CC-222SL 1 7 Cassette operating 1-­Introduction Other tape functions and features Tape counter The tape counter value increments when the tape is moving from left to right, and decrements when it moves from right to left. Use either of the RESET keys (main or remote) to reset the value to 0000. When the counter has been set to 0000, this position can be reached easily by pressing either of the RTZ keys (main or remote). [. . . ]