User manual TARGUS ACH93EU

[. . . ] Extension cords do not guarantee the required safety of the appliance (e. g. To guarantee the electrical safety of this appliance continuity must exist between the appliance and an effective grounding system. If there is any doubt, have the electrical system of the house checked by a qualified electrician. damaged it must only be replaced by a Miele Service technician with a genuine Miele power cord. [. . . ] After a short while, the estimated program duration for the program selected will appear in the display. Starting a program ^ Press the "Start / Stop" button. If additional options are selected, the corresponding indicators will also light up. the water softening) may be interrupted. Selecting a program Choose your program according to the type of load and soiling. Additional options can now be selected, if desired (see "Additional Options"). 34 Program Guide Program guide When to use Pre-rinse 1 2 Program sequence Main wash Interim rinse 1 2 Final rinse Drying Pots & Pans For normally soiled pots & pans with dried on food, and heavily soiled dishware, use 120% detergent recommended. X X X X X Normal as Program for completely required washing a full load of normally soiled dishware with the ability to adjust energy and water consumption based on the soil load of the dishware. For temperature sensitive glassware and lightly soiled dishware, use 50% detergent recommended. X as requi red X X X X China & Crystal X as required X X SaniWash X X X X Extra Quiet X X X X Rinse & Hold Usage: Electrical - 0. 01 - 1. 30 kWh Water - 1. 1 - 5 gal (4 - 19 l) 35 Use Time display Before the program starts, the time display shows the running time of the selected program in hours and minutes. During the running program the remaining time is shown in the time display. Symbols will appear to indicate the current stage of the program: 1 8 % ( G O Standby A few minutes after the last key is pressed or at the end of the program the dishwasher will switch into Standby mode to save energy. The display and the indicators are turned off and only the Start/Stop indicator light flashes slowly. If you do not turn the dishwasher off after the program ends, it will turn completely off after a few minutes in standby mode (see "Settings - Optimize standby"). If refill salt and/or rinse aid or a fault are present in the display, the dishwasher will not switch to Standby mode. Pre-wash / Soak Main wash Interim rinse Final rinse Drying Finished The time displayed may vary with the same program. Once selected, the function will remain active for all programs until the setting is changed. 39 Additional options Delay start The start time of a program can be delayed from 30 minutes to 24 hours. When using the "Delay Start" function, make sure that the detergent compartment is dry before adding detergent. Otherwise the detergent could stick together and not completely rinse out. ^ Set the desired delay start time with the "Delay start" button. If you press and hold the "Delay start" button, the time will automatically count up to 24:00 h. To start again at 30 minutes, press the "Delay start" button twice. If, after you have set the delay start time, you do not press the Start / Stop button within a few seconds, the display will revert to showing the program duration. The display shows the remaining time, the indicator "Delay start" goes out and the "Start / Stop" indicator light comes on. , To prevent children from coming into contact with the detergent: Only add detergent just before starting the program, i. before you press the Start / Stop button, and lock the door with the child safety lock. Starting a program before the Delay start has elapsed: A program can be started before the Delay start time has elapsed. The "Delay start" indicator light goes out and the "Start / Stop" indicator light flashes. The "Start / Stop" indicator light comes on. 40 Settings menu The "Settings" menu allows you to change standard settings Opening the "Settings" menu ^ Press the K button to turn the dishwasher off. [. . . ] Do not modify the plug provided with the appliance; if it will not fit the outlet, have a proper outlet installed by a qualified electrician. If there is any question concerning the proper electrical connection or grounding of this appliance to the power supply, please consult a licensed electrician or call Miele's Technical Service Department: U 1-800-999-1360 V 1-800-565-6435 Specifications The dishwasher comes equipped with a 4 ft (1. 2 m) power cord with a molded plug for connection to 120 V, 60 Hz, 15 A grounded receptacle. 65 Electrical connection Hardwired electrical connection It is possible to hardwire this appliance to an existing power cable. , Prior to making a hardwire , CAUTION: Before servicing, disconnect the power supply by either removing the fuse, shutting off the power main or manually "tripping" the circuit breaker. Installation work and repairs should only be performed by a qualified technician in accordance with all applicable codes and standards. Repairs and service by unqualified persons could be dangerous and the manufacturer cannot be held responsible. Before connecting the appliance to the power supply, make sure that the voltage and frequency listed on the data plate correspond with the household electrical supply. [. . . ]