User manual TALLYGENICOM T6200

[. . . ] A PRODUCT FROM TALLYGENICOM Line Printer Operator Manual Serial · Parallel · Twinax · Coax · TCP/IP T6200 Series Including IPDS This Manual is published by Tally Printer Corporation for use with the computer printer described herein. Translations, reprinting or copying by any means of this manual, complete or in part, in any different form requires our explicit approval. Tally Printer Corporation reserves the right to revise this manual without notice, for any reason. This includes, but is not limited to, utilization of advances in the state-of-the-art and changes in the equipment or configuration thereof. [. . . ] The current value of the right and left margins reflects a physical location on the form, and therefore, changes when the CPI setting changes. If the physical location of the right or left margin does not exactly correspond with a line position after changing the CPI (characters per inch) setting, there will be no current setting indicator (asterisk). Horz Adjust The print position on the form may be adjusted horizontally in increments of 1/30th an inch. Vert Adjust The print position on the form may be adjusted vertically in increments of 1/72nd an inch. Print to End Of Form (EOF) Before changing paper it is best to print to the end of the current form. This parameter allows you to set up the printer to print to the end of the form automatically. The settings are On and Off, with the default at Off. CAREFUL! For Print to EOF to function properly the last print line of the form must come before the perforation. If the Form Length setting allows printing to go over a perforation, it is possible for the printer to continue printing in a paper out situation without any paper in the printer, which may damage the printer. If Print to EOF is ON: The printer automatically prints to the end of the form then stops. The display reads Paper Out, the alarm sounds, and the FAULT indicator illuminates. After you load paper, ensure that the platen gap is closed, adjust the top-of-form location and make 3­10 Chapter 3: Printer Menus and Configuring Your Printer sure the paper is feeding correctly. When you are ready, depress the Clear key to clear the fault condition, then place the printer Online and continue printing. If Print to EOF is OFF, you have two options: Option 1: Load a new supply of paper into the printer. After paper has been loaded, set the correct top-of-form location and check for proper paper feed. When you are ready, depress the Clear key to clear the fault condition, then place the printer Online and continue printing. The printer will start printing where it left off, which may cause improper form and print location alignment. The printer prints to the end of the current form, then the display reads Paper Out and the FAULT Indicator illuminates. After loading paper, set the correct top-of-form location and check for proper paper feeding. When you are ready, depress the Clear key to clear the fault condition, then place the printer Online and continue printing. The Paper Out Sensor will not work unless the Top-Of-Form location has been set properly (see Chapter 2). Quick Access This feature provides a way for the printer to position printed forms for quick tearoff access. When Quick Access is enabled, the paper is moved to the tear position by pressing the Enter key. [. . . ] 17 CPI NLQ 994 #7 Graphics Performance 1122 T6215 1500/1285 1500/1285 1500/1285 1125/900 1125/900 1125/900 600/500 450/375 450/375 187 125 62 3660 2460 62, 000 1645 775 780 2200 2200 780 990 T6212 1200/1000 1200/1000 1200/1000 900/720 900/720 900/720 480/400 360/300 360/300 150 100 50 2928 1968 49, 600 1316 620 624 1760 1760 624 792 S­2 Specifications Lines Per Inch Ten Lines Per Inch (LPI) settings are available through the Control Panel. In some emulations the availability of certain LPIs is restricted. Paper Movement Speed Your printer has a normal slew speed of 36 inches per second. When printing in Heavy Forms mode, the maximum slew speed is decreased to 20 inches per second. Languages and Character Sets Up to 34 Language Character Sets with up to 192 characters (some emulations have fewer character sets with 256 characters) each are available on your printer. In addition, the ANSI and DIN character sets are available for use with the OCR-A and OCR-B type styles. [. . . ]