User manual TALLYGENICOM T2240-24

[. . . ] Conformity with the above mentioned Directives is indicated by the CE symbol attached to the device. Note: Conformity may be affected by: using interface cables not complying with the specifications non-observance of important instructions in the operator's manual installing components not approved for this device by the manufacturer unauthorized manipulation Dieses Gerät erfüllt die Anforderungen der Europäischen Normen durch Einhaltung der Richtlinie des Rates vom 3. The paper used is made of raw materials treated with a chlorine-free bleaching process. Only trained and qualified personnel may open covers or remove parts that are not explicitly shown and described in the User Guide as being accessible to the operator. [. . . ] The carton and the packing materials will be necessary for moving or transporting the printer. Place the printer on a stable, flat and non-slip surface in such a way that it cannot fall down. Ensure easy access to the control panel and the paper feeders and leave sufficient space for the paper ejected. If frequent forward and return feed movements will be performed with fanfold paper, you should position the printer as illustrated in the figure. When choosing a suitable place for your printer, you should also observe the following: Never place the printer near sources of easily inflammable gas or explosive substances. If you cannot avoid placing the unit near a window, protect it from sunlight with a curtain. S Position the printer near the computer to which it will be connected. Please open the printer package and check that all the following items are included. Never switch on the printer when it is not set to the correct voltage since this could cause severe damage. Connect the power cable to the printer's power inlet as shown in the figure. Connect the printer-end connector of the data cable to the female interface connector and secure it with the spring clips. The power switch, which is used for switching the printer on and off, is located at the right side of the printer. You can control printer operation using the control panel and the keys. If Load is displayed above this key, no paper is loaded in the printer; press the key to feed paper to the printing position. Tear key: Activates the tear function when fanfold paper is loaded Step feeds, line feeds and form feeds can be performed via the control panel only in this mode (see page 15). Short keypress: Line feed (LF) Long keypress: Form feed (FF) Short keypress: Micro-step return Long keypress: Constant paper feed return Short keypress: Micro-step forward Long keypress: Constant paper feed forward Clears the paper path with paper loaded and activates paper path quick selection (see page 14). In this mode, the following settings are available: Sets the font and the number of characters per inch (Char menu). Paper path (Paperway menu) Tear position and first printing line (Adjust menu) Other menu settings (Menu) For information on how to enable access to these options as well as about the options available, refer to the online documentation on the CD-ROM, chapter 1, Operation (Unlock the menu mode). The first line of the display informs you about whether the printer is in Online or in Offline mode and about the paper path selected (Trac. Pull the Latch Levers near the right and left ends on the Access Cover to the front, and detach the entire Access Cover. Align the part "A" on the left side of the Ink-ribbon Cartridge to the two hooks of the printer, push the cartridge all the way until it clicks. Do not detach the shield that has been attached to the Ribbon Guide; it is necessary to protect the ribbon. [. . . ] When single sheets were in use and you want to change over to fanfold paper mode, proceed as described below. for information on how to select a font permanently , refer to online documentation on the CD-ROM , chapter 1 (Menu description table). Printing method Print width Print speed (bidirectional) serial printing with 9-pin matrix print head narrow printer 80 characters at 10 cpi wide printer 136 characters at 10 cpi LN-Draft Draft NLQ 413 cps at 10 cpi 310 cps at 10 cpi 77 cps at 10 cpi serial printing with 24-pin matrix print head narrow printer 80 characters at 10 cpi wide printer 136 characters at 10 cpi Draft 409 cps at 10 cpi Draft Copy 275 cps at 10 cpi NLQ/LQ 92 cps at 10 cpi 5, 6, 7. Character densities Graphics print density Ribbon life Acoustic noise levell Dimensions Weight Power supply Power consumption Operating environment Print head specifications Cut sheets Paper weight Width Length Paper weight Width Length Paper weight Width/Length Form thickness Number of copies 60 ­ 120 g/m2 narrow printer: 76 ­ 220 mm / wide printer: 76 ­ 420 mm 76 ­ 559 mm 60 ­ 120 g/m2 narrow printer: 76 ­ 254 mm / wide printer: 76 ­ 420 mm 76 ­ 559 mm original: 45 ­ 65 g/m2 / copy: 45 ­ 56 g/m2 / last page: 45 ­ 65 g/m2 see simple forms max. [. . . ]