User manual TAG MCLAREN AUDIO 60IRV

[. . . ] record selector knob input selector knob mode selector knob power LED volume knob headphone socket power button RECORD INPUT MODE VOLUME tuner cd aux tape 1 tape 2 tape 3 tape 1 tape 2 tape 3 aux tuner cd pre mute integrated pre - power pre - power av integrated amplifier 60iRv contents 0 2 welcome 0 8 key features 1 0 getting started 1 4 selecting an input 1 6 operating modes 2 1 volume control 2 2 muting 2 3 headphones 2 4 grounding 2 5 connecting loudspeakers 3 3 running in and warming up 3 4 care and maintenance 3 6 technical data 4 0 international standards 1 right channel 2 2 left channel 1 mute LED remote control window fuse carrier loudspeaker terminals (right) loudspeaker terminals (left) power amplifier input sockets tape in/out sockets input sockets 220-240V ~ 50-60Hz Fuse: T2. 5A L 250V OUTPUT OUTPUT in 1 out 2 out 3 in out TA P E 2 in out 1 in aux SOURCE tuner cd left POWER AMP right PRE AMP left left left right right right made in United Kingdom serial number 60R 1234567 integrated amplifier 60iRv ground ac supply socket preamplifier output sockets ground terminal Specification shown may var y for different countries welcome to a new partnership . i n h i - p e r fo r m a n c e , h i - f i d e l i t y All TAG companies perpetually strive for, and achieve, excellence and highperformance in every area of their business. These qualities are demonstrated in the fastidious standards that make TAG Heuer Derek Scotland (on the left) ­ Technical Director Peter Stevens ­ Chief Industrial Designer Dr. Zucker ­ Chief Executive TAG McLaren Audio has been created with celebrating a TAG McLaren victor y one aim in mind: to produce the best highfidelity audio and audio-visual systems available. [. . . ] It does not affect the output from the record sockets (TAPE out 1, out 2 and out 3). volume Turn the VOLUME knob clockwise to increase volume and anticlockwise to decrease volume. When supplied with an input with a peak level of 2 V rms (the typical output from a CD player), your 60iRv gives its full rated output with the VOLUME knob in the middle of its travel. Turning the knob past this point may distort the sound and could damage your loudspeakers. Alternatively you can use the volume + button on the remote control to increase volume and the volume ­ to decrease it(2). VOLUME source in (connect to external power amplifier) pre-amp out This diagram shows the connections inside the 60iRv when it is set to pre-power mode preamp power amp 1. 2. In some operating modes, the preamplifier output is isolated (see page 16) When you use the remote control, the VOLUME knob on the front panel will turn automatically. Make sure that nothing interferes with the free movement of the knob when you use the remote control 20 21 muting headphones The mute controls switch off the signal from the loudspeaker terminals, the headphone socket and the preamplifier output. There are two ways of manually muting the output: you can use the MODE selector on the front panel or you can press the mute button on the remote control. An LED on the front panel indicates that the 60iRv is muted. MODE headphone connection Turn the VOLUME down before you connect your headphones. Insert the headphone plug into the 1/ (6. 3 mm) stereo jack 4" socket on the front panel of your 60iRv(1). loudspeaker muting mute pre integrated pre - power pre - power av When you plug in your headphones, the loudspeaker and preamplifier outputs are automatically muted(2). muting using the mode knob Turn the MODE selector until the mark on its side points to mute to switch off the output as described above. muting using the remote control Press the mute button on the remote control to switch the output on and off(1). The output will also switch back on if you turn the VOLUME knob. automatic muting The 60iRv also mutes briefly whenever you change an INPUT or a MODE until all voltages have stabilized. 1. If the 60iRv has been muted using the MODE selector then the mute button on the remote control has no effect If you want to use headphones which have the smaller 1/8" (3. 2 mm) jack plug, you should obtain an adaptor from your retailer. Remove the adaptor from the socket when you are not using the headphones or the output will remain muted Plugging in headphones also isolates the power amplifier input 2. 22 23 grounding connecting loudspeakers The AC mains supply normally operates at either 50 or 60 Hz (depending on which country you are in). Under some circumstances, this can cause an audible hum in your loudspeakers. Should you have any problems with hum in your system, please contact your retailer. The connection between your 60iRv and your loudspeakers is crucial to the sound quality of your entire audio system. Your 60iRv is specified to operate with 8 loudspeakers, but it can be used with 4 loudspeakers. The 60iRv may also be connected to loudspeakers which have a transient impedance of less than 4 (1). Always use high-quality loudspeaker cable. avoiding hum To minimise the possibility of mains hum in your system: do not link the ground terminals of separate audio units together. use screened cable for your signal connections and keep the left and right channel cables close together. loudspeaker terminals grounding your system All the units in the TAG McLaren Audio F3 Series are double insulated and do not require safety ground connections. Although a ground terminal is provided on the 60iRv, for your convenience your system does not need to be connected to ground (audio engineers call this `floating`). However, if you want to ground your system, please contact your retailer who will be able to assist you. On the back of your 60iRv, you will find four pairs of loudspeaker terminals, each pair consisting of one red and one black terminal. right and left) to allow you to `bi-wire' the loudspeakers as explained on page 28. OUTPUT 1 right channel 2 1. These ratings are for music signals only. [. . . ] Next, connect PREAMP out 1 left on the 60iRv to INPUT left on the 60P. On each amplifier connect one of the stereo outputs to the high-frequency driver and the other to the low-frequency driver. right speaker hf left speaker using monoblocs You may prefer to use two monoblocs(1) (such as our 125M), in conjunction with your 60iRv. This arrangement has the added advantage of allowing you to place each amplifier close to the loudspeaker it is feeding, thus enabling you to connect them together with short cables. Connect PREAMP out left on the 60iRv to INPUT on one of the monoblocs and PREAMP out right to INPUT on the other monobloc. [. . . ]