User manual TAG HEUER MONACO SIXTY NINE

[. . . ] The warranty does not cover bracelets, crystals or batteries, or any damage to the case or movement caused by moisture that might have entered the watch as a result of improper handling. Should you need to return this watch, we recommend that you wrap your TAG Heuer carefully so as to avoid any damage and send it by registered mail to the nearest official TAG Heuer Service Center, or take it to your local authorized dealer. You will find a list of Official TAG Heuer Service Centers at the end of this booklet. They will supply you with the address of your nearest authorized TAG Heuer dealer upon request. [. . . ] At this point there is enough room to pivot the watch on its supports. Rotate the watch through 180°, holding its sides between your thumb and index finger (figs. Push the watch down vertically until you hear it click into place between the support's minibearings. While pushing the watch back down, be sure to keep the dial horizontal (fig. 6 Watch hands Hours Minutes Seconds 6 7 SETTING THE TIME ON THE ANALOG FACE The crown has 2 positions (fig. Position 1: manually rewinding the movement In this position, you can rewind the mechanical movement by rapidly rotating the crown. Position 2: quickly setting the time To adjust the time, pull the crown out to position 2 and rotate it in the desired direction. Remember to always push the crown back into position 1 once the time has been set. Broken shaft Caution: The mechanical movement of your Monaco Sixty Nine has a special shaft that links it to the crown through a tube. This "broken shaft" is made up of two parts: ­ a male section, which fits into the movement ­ a female section, which is attached to the crown If you pull the crown out too abruptly when setting the time quickly, the shaft may come away from the movement. If this happens, simply reinsert the shaft into the tube, pushing it in carefully with your thumb while turning the crown slightly so that it gently connects with the male section of the movement. To check that the shaft has been properly reinserted, try setting the time. If you are not certain, we recommend that you take the watch to your nearest authorized dealer. DISPLAY MODES ON THE DIGITAL FACE The digital display of your Monaco Sixty Nine has six different modes: > T1 mode: > AL mode: > F1 mode: > BEST LP mode: > Ch mode: > T2 mode: Main time and date Alarm F1 timekeeping Best lap (LP = LAP) ­ for consulting lap times stored in the memory Chronograph Second time zone 9 OVERVIEW OF THE BUTTONS Your Monaco Sixty Nine has four push buttons: A, B, C and D (fig. Their functions differ depending on the mode selected and the way they are pressed. There are two ways of pushing the buttons: ­ short (less than 2 seconds) or ­ long (more than 2 seconds) Caution: water-resistance cannot be guaranteed if the buttons are pressed under water. 8 9 MODE DETAILS AND BUTTON FUNCTIONS T1 mode Main time (hours-minutes-seconds) and date (day of the month, day of the week) are shown. "T1" appears for three seconds, followed by "AL" if the alarm has been set (fig. If the 12-hour clock is selected, this is indicated in the center-right of the display (fig. In T1 mode, the button functions are: A B C D D short push = activates standby mode (screen goes blank)* = no function. short push = selects the next mode long push = selected mode can be set. 9 Hours Minutes Seconds In AL mode, the button functions are: A A B C D D long push = alarm is set or unset beep means that the alarm is set long push = alarm test sound is set = activates the backlight for six seconds short push = selects the next mode long push = selected mode can be set fig. Therefore, to time one lap only, button A should be pressed to start, then A again to store the result in the memory and then B to stop timing. When the memory is full, the timings of laps 1 to 79 are kept and each new lap is stored in position 80, thereby erasing the time of the previous lap. [. . . ] The months are shown as: JAN, FEB, MAR, APR, MAY, JUN, JUL, AUG, SEP, OCT, NOV, DEC. ­ To activate the setting mode, press button D for more than two seconds. 23 Setting the alarm ON or OFF: In AL mode, to set the alarm ON or OFF, press button A for more than two seconds. ­ To activate the setting mode, press button D for more than two seconds. [. . . ]