User manual SYSTEM AUDIO SUBELECTRO 175 2010

[. . . ] However, under certain conditions it may be possible for an installation in these applications. Please contact the nearest Miele dealer or the Miele Technical Service Department with specific requirements. This dishwasher must be installed under a continuous countertop secured to adjacent cabinetry. Do not, under any circumstances, cut the intake hose or submerge in liquid. [. . . ] Tipping the machine slightly to the rear, if possible, will make adjusting the front legs easier. Make sure the machine is level when adjustments are complete. ^ Insert the tab of each bracket into the guide holes on top. Stone or marble counterops: Do not install these mounting brackets if the counter is made of an extremely hard material. The securing screws for the mounting brackets are not suitable for such materials. ^ Place the skis, with the ratchet at the rear, under the dishwasher legs. 14 Installation 4. Install the dishwasher under the countertop The dishwasher must be installed so that the water and electricity supplies can be accessed through an adjacent cabinet. ^ Make certain that there are no rough edges that could damage the power cord or hoses. If metal cabinets are used, place the supplied rubber grommet around the edge of the opening before passing the cable through. , WARNING - Fire hazard Do not cover or crush the plug of an electric appliance. Ensure that the cabinet opening for the dishwasher provides ample space for the plug. (648 - 718 mm) Thickness: At least 3/4" (18 mm) where the mounting bracket is to be screwed in position. 16. 5 lbs (7. 5 kg) Panel Height = HTC - TKH HTC = Height to the underside of countertop TKH = Toe Kick Height 17 Installation The door panel is attached to the dishwasher using the mounting bracket that comes secured to the front of the unit. To remove the bracket: ^ Open the door 2 - 4" (5 - 10 cm). ^ Loosen the bracket retaining screw (black arrow) located on each side of the machine door. ^ The panel can be raised or lowered by turning the lower screw on each side of the dishwasher door. If the steam deflector is installed, the mounting bracket holes must align with the slots in the steam deflector. Make certain that the white rubber seal located at the top, outer edge of the dishwasher is tight against the bottom of the countertop. If in doubt on how to secure the dishwasher, please call Miele's Technical Service Department. ^ Using flat head screws, secure the dishwasher to the countertop by screwing through both the mounting bracket and the steam deflector. 23 Installation For openings exactly 23 5/8" (60 cm) wide: , The side mounting holes should only be used for securing the dishwasher if the opening is exactly 23 5/8" (60 cm) wide. Use of this method on larger openings can damage the machine and cause leaks. Be careful not to screw into an adjacent appliance. ^ Open the dishwasher door and remove the caps covering the mounting holes on the outer edge of the wash cabinet. ^ Fasten the dishwasher to the adjacent cabinets using the supplied screws and bushings. A bushing must be placed over the screw before inserting it into its mounting hole. If the door remains in this position when released, the springs are adjusted correctly. If it closes on its own, the tension on the springs need to be decreased. ^ To adjust the door springs use a T20 Torx or a small slotted screwdriver and turn the screw located behind the door in the upper front strip, on the left hand side of the dishwasher. ­ turn clockwise to increase the tension ­ turn counterclockwise to decrease the tension. [. . . ] Do not modify the plug provided with the appliance; if it will not fit the outlet, have a proper outlet installed by a qualified electrician. If there is any question about the proper electrical connection or grounding of this appliance to the power supply, please consult a licensed electrician or call Miele's Technical Service Department: USA 1-800-999-1360 CDN 1-800-565-6435 30 Installation Power outlet The power outlet for the appliance must be installed within a cabinet, on a wall adjacent to the undercounter space in which the dishwasher is located. An opening through the partition between the compartments of 1 1/2" (3 to 4 cm) can be made to allow the plug to pass through. Permanent Connection (Hard Wiring) For hard wiring, the power cord must be disconnected from the terminal box located at the lower left front of the dishwasher, behind the toekick and service panel. [. . . ]