User manual SYMPHONIC 19TVCRMKIIIS

[. . . ] RETAIN INSTRUCTIONS - The safety and operating instructions should be retained for future reference. HEED WARNINGS - All warnings on the appliance and in the operating instructions should be adhered to. FOLLOW INSTRUCTIONS - All operating and use instructions should be followed. EXCEPTION: A product that is meant for uninterrupted service and, that for some specific reason, such as the possibility of the loss of an authorization code for a CATV converter, is not intended to be unplugged by the user for cleaning or any other purpose, may exclude the reference to unplugging the appliance in the cleaning description otherwise required in item 5. [. . . ] - When selecting analog channel 12 1 2 ENTER CH RETURN VOL. MUTE CH 1 Using [VOL. · The volume bar is displayed at the bottom of the screen when adjusting the volume. · Same operation is available with [VOLUME X/Y] on the top panel of the main unit. Volume 20 - When selecting digital channel 12-1 Be sure to press [­] before entering the minor-channel number. 1 2 1 ENTER · If the channel broadcasts NTSC and ATSC both and you don't press [­], then you will receive the NTSC channel only. The moment you press [­], the lowest memorized digital channel will be displayed. · When you press [CH RETURN], the previously selected channel will be selected. NOTE: · In the DTV broadcasting, one channel sometimes broadcasts multiple programs depending on the air time. In this case, the main channel is called major channel and the minor-channel is called minor channel. · The volume bar display will automatically disappear in a few seconds. · To release the Mute status, press [MUTE] again or press [VOL. X/Y]. Mute About minor-channel broadcasting: There may be different programs being broadcast on minor-channels through a single channel from ATSC. You can watch each minorchannel program being broadcast by selecting one of the minor-channels. · "Mute" is displayed on the screen for a few seconds. 18 EN STILL MODE You can freeze the image shown on the screen. 1 4 7 SETUP When the broadcasting has SAP and stereo audio. . . 2 5 8 0 3 6 AUDIO SAP / STEREO SAP / STEREO When the broadcasting has SAP and monaural audio. . . 9 STILL SAP / MONO SAP / MONO SCREEN MODE When the broadcasting is having only monaural audio. . . MONO 1 Still DTV · The audio is not paused and keeps on reading out. · If the digital signal is gone or protected, the image will remain paused and the audio will be muted. [Wide] Wide will display the center of the picture as original size and the either side of the picture will be elongation. The size of the picture will depend on the original signal. [Full] A picture will be displayed at 16:9 size as it is. [Zoom] Zoom will display a 16:9 picture without changing its horizontal to vertical ratio, at its maximum size. [Expand] Expand will display a 16:9 picture with horizontal elongation. 21 EN WATCHING TV SCREEN INFORMATION You can display the currently selected channel number or other information such as the audio mode on the screen for checking. AUDIO DTV In the digital mode, the detailed information for the currently selected channel such as the Program guide is displayed. 7 SETUP 8 0 9 STILL 1 Display the detailed information for the channel. 4 lines displayed) (4) Channel number (5) Audio language ("Other" is displayed when the audio language cannot be acquired, or the acquired languages are other than English, Spanish or French. ) (6) Effective scanning lines and scan mode (7) Program definition (8) Program aspect ratio (9) Program rating (10) CC (Not available if the CC set to "Off") (1) Buffy Vampire Slayer SCREEN MODE ENTER BACK INFO CH RETURN VOL. MUTE CH TV In the analog mode, the currently selected channel number and the audio mode are displayed. 1 Display the channel number and the audio mode. The currently selected channel number, the audio mode, the type of resolutions for video signal, TV aspect ratio, CC and TV rating are displayed at the top-right of the screen. 6 SAP / STEREO 480i 480i SD SD 4:3 4:3 TV-PG DLSV CC CC (2) HDTV (4) 6-1 English 1/2 1080i 1080i HD HD 16:9 16:9 TV-PG DLSV CC CC A quarter-century ago, which may now qualify as the good old days of newspapering, run-of-paper sales accounted for 80 percent of the industry's advertising revenues. Department stores and supermarket were (5) (6), (7), (8) (3) (9) (10) · To clear the display, press [BACK] or [INFO] again. NOTES: · When the program guide is displayed in more than 5 lines, use [ K/ L] and scroll for reading. · "No description provided" is displayed when the program guide is not provided. · The following screen is displayed when connecting to external devices: e. g. ) When using VIDEO1 INPUT jack for connection Video1 480i 480i SD SD TV-PG DLSV CC CC 22 EN OPTIONAL SETTINGS SLEEP TIMER The Sleep Timer function will automatically turn off the power of the unit at a preset time. POWER INPUT SLEEP SELECT SETUP SCREEN This section describes the overview of the setup screen displayed when you press [SETUP]. The setup screen consists of the function setting items below. AUDIO 1 4 7 SETUP 2 5 8 0 3 6 9 STILL · To exit settings. · You can adjust the picture quality (Picture Mode, Brightness, Contrast, Color, Tint, Sharpness, Color Temp. , and Energy Saving). (Refer to "PICTURE ADJUSTMENT" on page 24. ) · You can automatically scan the receivable channels and watch or skip the channel as necessary. (Refer to "AUTOSCAN" on page 13. ) · You can change the display format for Closed Caption as well as varied font styles, which displays the dialogue of a TV program or other information across the screen. [. . . ] Such chemicals may cause damage and discoloration to the exposed surfaces. IR SIGNAL CHECK If the remote control doesn't work properly, You can test if the remote control sends out the infrared signal with an AM radio or a digital camera (including built-in camera of cellular phone). · With an AM radio: Tune an AM radio to a station with no broadcasting. Sound will be fluttering when you press any button and the radio receives the signal. · With a digital camera (including builtin camera of cellular phone): Direct a digital camera to remote control, press and hold any button on remote control. [. . . ]