User manual SYLVANIA 6637LCT

[. . . ] 37 inch Digital / Analog LCD TV Owner's Manual 6637LCT A 6637LCT POWER INPUT SLEEP SELECT 1 4 7 SETUP 2 5 8 0 3 6 AUDIO 9 STILL SCREEN MODE ENTER BACK INFO CH RETURN VOL. MUTE CH HIGH-DEFINITION TELEVISION TO RECEIVE DIGITAL/ANALOG SIGNAL, YOU MUST CONNECT ANTENNA. IF YOU NEED ADDITIONAL ASSISTANCE WITH SET-UP OR OPERATING AFTER READING OWNER'S MANUAL, PLEASE CALL TOLL FREE 1-800-968-3429, OR VISIT OUR WEB SITE AT http://www. SylvaniaConsumerElectronics. com WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE. CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. The important note is located on the rear of the cabinet. THIS SYMBOL INDICATES THAT DANGEROUS VOLTAGE CONSTITUTING A RISK OF ELECTRIC SHOCK IS PRESENT WITHIN THIS UNIT. THIS SYMBOL INDICATES THAT THERE ARE IMPORTANT OPERATING AND MAINTENANCE INSTRUCTIONS IN THE LITERATURE ACCOMPANYING THE APPLIANCE. IMPORTANT SAFEGUARDS 1. READ INSTRUCTIONS - All the safety and operating instructions should be read before the appliance is operated. [. . . ] The mute function, which turns the sound off and on, will also be described. BACK INFO CH RETURN VOL. MUTE CH - When selecting digital channel 12-1 Be sure to press [­] before entering the minor channel number. 1 2 1 ENTER [VOL. · The same operation is available with [VOLUME X/Y] on the top panel of the main unit. · The volume bar will be displayed at the bottom of the screen when adjusting the volume. Volume 20 · If the channel broadcasts NTSC and ATSC both and you don't press [­], you will receive the NTSC channel only. The moment you press [­], the lowest memorized digital channel will be displayed. · Press [CH RETURN] to return to the previously viewed channel. NOTE: · In DTV broadcasting, one channel sometimes broadcasts multiple programs depending on the air time. In this case, the main channel is called major channel and the minor channel is called minor channel. · The volume bar display will automatically disappear in a few seconds. [MUTE] · Press [MUTE] to turn off and on the sound. Mute · "Mute" is displayed on the screen for a few seconds. X/Y] ([VOLUME X/Y]) to release the Mute status. About minor channel broadcasting: There may be different programs being broadcast on minor channels through a single channel from ATSC. You can watch each minor channel program being broadcast by selecting one of the minor channels. 18 EN STILL MODE You can freeze the image shown on the screen. 1 4 7 SETUP When the broadcasting has all audio. . . SAP / STEREO SAP / MONO 2 5 8 0 3 6 AUDIO SAP / STEREO When the broadcasting has stereo audio and monaural audio. . . 9 STILL SCREEN MODE MONO / STEREO MONO / STEREO When the broadcasting has SAP and monaural audio. . . 1 Still MONO (cannot be switched. ) STEREO : Outputs stereo-audio SAP : Outputs second audio program MONO : Outputs mono-audio DTV · The audio is not paused and keeps on reading out. · If the digital signal is gone or protected, the image will remain paused and the audio will be muted. · The Still function will be released after 5 minutes. 2 Canceling Still function. · The Still function will be canceled by pressing any button while Still function is working. NOTE: · Press any key except [POWER] to cancel still mode. When you press [AUDIO], the currently selected language and the number of available languages will be displayed on the screen. 6-1 English 1/3 Press [AUDIO] to cycle through available audio languages. SELECTING AUDIO CHANNELS This section describes how to switch the audio in the analog mode and how to switch the audio language in the digital mode. AUDIO English 1/3 Spanish 2/3 Other 3/3 · Available languages differ depending on the broadcast. · The information display will automatically disappear in one minute. NOTE: · Pressing [AUDIO] does not control external audio source. 7 SETUP 8 0 9 STILL SCREEN MODE TV When you press [AUDIO], the currently selected audio mode will be displyed on the screen. 6 SAP / STEREO Press [AUDIO] to cycle through available audio channels. 19 EN WATCHING TV Pause the image. · When you press [STILL], the image shown on the screen is paused. SAP / MONO SAP / MONO When the broadcasting is having only monaural audio. . . ACCESSING EXTERNAL DEVICES Use your remote control to access DVD recorders, home audio systems and other external devices when they are connected to your television. POWER INPUT SLEEP SELECT · When you press [INFO], the current external input mode, the type of resolutions for video signal, TV aspect ratio, CC and TV rating will be displayed at the top-right of the screen. · The information display will automatically disappear in 1 minute. 1) When using VIDEO1 or S-VIDEO1 input jack 1 4 7 SETUP 2 5 8 0 3 6 AUDIO 9 STILL Video1 480i SD TV-PG DLSV CC SCREEN MODE ENTER BACK INFO 2) When using VIDEO2 or S-VIDEO2 input jack Video2 480i SD CH RETURN VOL. MUTE CH TV-PG DLSV CC Use your remote control to select external component. · When you press [INPUT SELECT] or [CH L] on the remote control, the input mode will be switched as below. TV/DTV channel Video1 3) When using COMPONENT1 input jacks Component1 1080i HD NONE 4) When using COMPONENT2 input jacks Component2 1080i HD Video2 NONE Component1 5) When using HDMI IN jack Component2 HDMI 1080i HD 16:9 NONE HDMI · Pressing [CH K] on the remote control reverses direction. · To use the VIDEO1 or S-VIDEO1 input jack on the TV, select "Video1". · To use the VIDEO2 or S-VIDEO2 input jack on the TV, select "Video2". [. . . ] If the infrared light appears through the camera, the remote control is working. LCD CLEANING Wipe the LCD of the TV with a soft cloth. Before cleaning the LCD, disconnect the power cord. SERVICING Should your unit become inoperative, do not try to correct the problem yourself. Turn off the TV, unplug the power cord and call our toll free customer support line found on the cover of this manual to locate an authorized service center. 34 EN SPECIFICATIONS GENERAL SPECIFICATIONS Television System: ATSC NTSC-M TV Standard ELECTRICAL SPECIFICATION Sound Output: 5W, 8 ohm x 2 OTHER SPECIFICATIONS Remote Control: Operating Temperature: Digital encoded infrared light system Closed Caption System: §15. 119/FCC (Analog CC) §15. 122/FCC (Digital CC) Channel Coverage (ATSC/NTSC) VHF: 2 ~ 13 UHF: 14 ~ 69 CATV: 2 ~ 13, A ~ W, W+1 ~ W+94, A-5 ~ A-1, 5A Tuning System: Channel frequency synthesized tuning system Channel Access: Direct access keyboard, Programmable scan, and Up/down Terminals Antenna Input: VHF/UHF/CATV 75 ohm unbalanced (F-type) S-Video Input: Mini DIN 4-pin jack x 2 Video Input: RCA jack x 2 Audio Input: RCA jack (L/R) x 4 Component Video/Audio Input: One pin jack (Y) / 1Vpp x 2 Two pin jacks (Pb/Pr) / 700mVpp x 4 RCA jack (L/R) x 4 HDMI / Audio Input: HDMI jack RCA jack (L/R) x 2 Coaxial Digital Audio Output: One pin jack, 500mVpp Analog Audio Output: RCA jack (L/R) x 2 Stereo Sound System Speaker · Designs and specifications are subject to change without notice and without our legal obligation. · If there is a discrepancy between languages, the default language will be English. 35 EN MISCELLANEOUS / SPECIFICATIONS 5°C to 40°C (41°F to 104°F) Power Requirements: AC120V, 60Hz Power Consumption (Maximum): 205W LCD: 37" wide XGA panel (1, 366 x 768 pixels) Dimensions: <Without stand> H : 26-9/16" (674mm) W: 37-5/16" (948mm) D : 4-12/16" (120mm) <With stand> H : 28-5/16" (718. 5mm) W: 37-5/16" (948mm) D : 12-13/16" (325mm) Weight: 52. 8 lbs. [. . . ]