User manual SYLVANIA 6309CA

[. . . ] REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. The caution marking is located on the rear of the cabinet. IMPORTANT SAFEGUARDS 1. Read instructions-All the safety and operating instructions should be read before the appliance is operated. 2. Retain Instructions-The safety and operating instructions should be retained for future reference. 3. Heed Warnings-All warnings on the appliance and in the operating instructions should be adhered to. 4. Follow Instructions-All operating and use instructions should be followed. [. . . ] BLANK REPEAT: Repeat playback from the beginning to a blank part, which is blank for more than 10 seconds. CORRECT WRONG PRECAUTIONS · Avoid moisture. Moisture condensation may occur 1 Select "USER'S SET UP" ­MENU­ TIMER PROGRAMMING PICTURE CONTROL SETTING CLOCK CHANNEL SET UP B USER'S SET UP LANGUAGE [ENGLISH] ZERO RETURN TIME SEARCH · · · on the tape if it is moved from a cold place to a warm place or visa versa. Before using a tape with these conditions, to avoid damage of the tape and your TV/VCR, wait until the tape has warmed to room temperature and the moisture has evaporated. Do not touch the tape with your fingers. Press the MENU button on the remote control. Press the PLAY/K or STOP/L button to point to "USER'S SET UP". Then, press the F. FWD/B button. 2 Select "ALL" or "BLANK" ­ USER'S SET UP ­ NORMAL PLAYBACK Make sure . . . · TV/VCR power must be turned on. Press the PLAY/K or STOP/L button to point to "REPEAT PLAY". Press the F. FWD/B or REW/s button repeatedly until your desired selection [ALL] or [BLANK] appears. RENTAL B REPEAT PLAY AUTO RETURN [OFF] [ALL] [OFF] 1 Insert a prerecorded tape 3 Exit the Repeat Play setting If the erase-protection tab has been removed, the TV/VCR will start playback automatically. Press the MENU button on the remote control to return to the TV mode. 2 To begin playback PLAY B 4 Start playback Press the PLAY button. Note: If any menu is activated on the screen, the PLAY button does not function. then, press the PLAY button. Press the PLAY button to start the Repeat Play. · Once you select the Repeat Play mode, it stays in effect even after you turn off the TV/VCR. If the tape was originally recorded in the SP or LP mode, the still picture may revert to black and white in addition to the "noise bars". This is normal. RENTAL PLAYBACK This function enables you to improve the picture quality when playing back worn cassettes such as rented tapes. 1 Select "USER'S SET UP" ­MENU­ TIMER PROGRAMMING PICTURE CONTROL SETTING CLOCK CHANNEL SET UP B USER'S SET UP LANGUAGE [ENGLISH] ZERO RETURN TIME SEARCH Press the MENU button on the remote control. Press the PLAY/K or STOP/L button to point to "USER'S SET UP". Then, press the F. FWD/B button. VERTICAL HOLD CONTROL In the Pause/Still mode only, when the picture begins to vibrate vertically, stabilize the picture by pressing the CHANNEL K or L button. NOTE: If there are video noise lines on the screen, reposition or reduce them. Refer to "NOISE CANCEL". 2 Set "RENTAL" to [ON] ­ USER'S SET UP ­ Press the PLAY/K or STOP/L button to point to "RENTAL". Press the F. FWD/B or REW/s button until [ON] appears. B RENTAL REPEAT PLAY AUTO RETURN [ON] [OFF] [OFF] 3 Exit the Rental setting TRACKING ADJUSTMENT · Tracking adjustment will be set automatically · (Digital Tracking function) when you start playback. However when playing pre-recorded tapes or tapes recorded on units other than your own, noise lines (black and white streaks) may appear on the playback picture. If this occurs, you can adjust the tracking control manually by pressing the CHANNEL K or L button until the streaks disappear. To return to the DTR function, stop the tape once and start playback again. Press the MENU button on the remote control to return to the TV mode. 4 Start playback Press the PLAY button to start playback. · Once you select the Rental mode, it stays in effect even after you turn off the TV/VCR. TO CANCEL THE RENTAL MODE Repeat steps [1] and [2], select [OFF] using the F. FWD/B or REW/s button on the remote control. [. . . ] Si desea recuperar canales seleccionados, usted podrá seleccionar directamente el canal deseado con los botones numerados del mando a distancia o con los botones CHANNEL K o L. AJUSTE DEL RELOJ Cerciórese. . . · La alimentación del televisor/videograbadora deberá estar conectada. En el ejemplo de abajo, el reloj va a ajustarse así: FECHA: 1 de mayo de 2002 HORA: 5:40 PM 1) Pulse el botón MENU en el mando a distancia. Pulse el botón PLAY/K o STOP/L para indicar "AJUSTE RELOJ". [. . . ]