User manual SWISHER LV5537S

[. . . ] All transportation charges, damage, or loss incurred during transportation of parts submitted for replacement or repair under this warranty shall be borne by the purchaser. Should you have any questions concerning this warranty, please contact us toll-free at 1-800-222-8183. The model number, serial number, date of purchase, and the name of the authorized Swisher dealer from whom you purchased the mower will be needed before any warranty claim can be processed. THIS WARRANTY DOES NOT APPLY TO ANY INCIDENTAL OR CONSEQUENTIAL DAMAGES AND ANY IMPLIED WARRANTIES ARE LIMITED TO THE SAME TIME PERIODS STATED HEREIN FOR ALL EXPRESSED WARRANTIES. [. . . ] Vehicle braking and stability are affected by the addition of this equipment. Do not fill the lawn vacuum to its full capacity without checking the towing capacities of the tow vehicle. SAFETY AND OPERATIONAL DECALS Replace decal immediately if damaged. Inc. OD55-TRIANGLE DANGER DECAL OD70142-DANGER STOP ENGINE DECAL OD38-CAUTIONS DECAL 4 ASSEMBLY INSTRUCTIONS 1. Align holes in frame and install 3/8-16X1" Hex Head bolt and lock nuts. (Figure 2) Insert hitch tube into the front of the hitch and lock in place with the snap pin (H11). Align fan/engine/pump assembly on lower slots of motor base with the rivets, pushing down and rearward to align the front holes. Unfold fabric bag frame and place into pockets at the corner of the bed. (Figure 5) Install tailgate by sliding downward into the rear channels. Open fabric bag and spread over the top frame stretching downward and slipping the plastic edge under the edge of the trailer bed rail. Attach the Velcro tabs around the rear frame section and zip the rear flap closed. Insert the bag adaptor into the bag sleeve at the front upper left hand corner Install upper tube onto blower and lock into place. (Figure 4) Assemble end of hose and a hose clamp over the round opening of boot and tighten clamp. PREPARING THE DECK BOOT · View the boot templates that are provided. Select the template that corresponds with the discharge opening of mowing deck. If a template does not exist for your mower, then one will need to be created. · To create a custom template, mark around your discharge opening on a piece of cardboard. · Tape the template to the face of the boot, locating the template approximately ½" from the front edge and ¼" down from the top. Mark outline of template onto the face of the boot using a white crayon, nail or scribe. · Drill a starting hole inside the outline, and then use a key-hole saw or equivalent to cut out the opening. · Position the boot over the deck opening and check for fit of cutout. Drilling of holes into your existing deck may be necessary, as well as drilling into the top of the boot. ATTENTION!WE HAVE MADE EVERY ATTEMPT TO PROVIDE HARDWARE TO MOUNT THE DECK BOOT TO VARIOUS LAWN MOWING MANUFACTURERS. DUE TO CONSTANT CHANGES IN DESIGNS OF MOWING DECKS SOME ADAPTATION MAY BE NECESSARY. 5 Be careful while lifting, not to bend latch. [. . . ] Store vacuum in a dry covered area or indoors. ONLY A QUALIFIED MECHANIC SHOULD MAKE ANY ADJUSTMENTS, DISASSEMBLY OR OTHER KINDS OF REPAIRS. 9 SERVICE PARTS Please have Model and Serial Numbers ready when ordering parts. Color cannot be guaranteed upon service parts. ITEM NUMBER 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 NOT SHOWN NOT SHOWN NOT SHOWN NOT SHOWN NOT SHOWN DESCRIPTION MOTORBASE BAG FRAME WELDMENT TRAILER REAR FRAME SECTION FRONT FRAME SECTION LATCH LATCH LOCK TONGUE IMPELLER BAG BAG FRAME SPREADER TAILGATE AXLE TIRES KNOB FRONT RING ENGINE BAG ADAPTOR TUBE - BLOWER ASSEMBLY BLOWER FRONT 1/4 - 20 X 1 1/2 BOLT 1/4 - 20 NYLOK NUT 3/4ID X 1 1/4OD WASHER 1/8 X 1 1/2 COTTER PIN 3/8 - 16 X 1 BOLT 3/8 - 16 NYLOK NUT 3/8 - 16 X 1 1/4 BOLT SPRING FOR IDLER ARM SAFETY HITCH PIN 5/16 - 18 X 1 1/4 SERRATED FLANGE BOLT 5/16 - 18 SERRATED FLANGE NUT BELLEVILLE WASHER 3/8 - 24 X 1 BOLT W/ LOCKTITE 5/16 - 18 X 6 1/2 BOLT 5/16 - 18 NYLOK NUT 1/4 X 1 Key Stock WIRING HARNESS LAWN VAC PLATE SWITCH MOUNTING INTERLOCK SWITCH 5/16-18 X 1/2 Serr. Flg Bolt HOSE CLAMP BOOT SUSPENSION ARM ADAPTOR PLATE PART NUMBER 5443 5412 5400 5437 5433 5439 5468 5421 5426 5420NL 5414 5463 5462 F44157LV 2079 5410 N/A 5407 5470 5405 NB162 NB180 NB195 NB126 NB604 NB182 NB618 BRS6 H11 NB253 NB170 699 NB238N NB680 NB181 9031 10784 5487TK 10885 NB252 5402 5403 5404 5467 5471 11 LAWN VACUUM OWNER'S MANUAL HOW TO ORDER REPAIR PARTS: Each Lawn Vacuum has its own serial number. The serial number for the Lawn Vacuum will be found on the left hand side of the motorbase. [. . . ]