User manual SWEEX MO251V2 QUICK_START_GUIDE

[. . . ] This enables you to simultaneously make calls and surf the Internet using the same telephone line. The signal comes from the wall socket or the meter cupboard and enters the splitter. It can be obtained from various DIY stores. Connecting the Sweex ADSL 2 Modem 1. Connect the power adaptor (included) to the rear of the modem and the mains socket. [. . . ] As a result they can get away with surfing on your Internet connection, and they may gain access to your shared folders and files on your network. Enter this code on each computer that wants to connect to that secured network. If you did not enter the network key into the router or modem yourself, ask the installer, manufacturer, supplier or provider for this code. Connecting the computer to the wireless network In the bottom left of your screen, go to "Start (Start) "Control Panel" (Control Panel). Then go to "Network and Internet Connections" (Network and Internet Connections). Or, if the Windows classic style is used: "Start" (Start) "Settings" (Settings) "Network Connections" (Network Connections). Right-click "LAN Connection" (LAN Connection) or "Wireless Network connection" (Wireless Network connection) and select "View Available Wireless Networks" (View Available Wireless Networks). 10 English version Always click "Refresh network list" (Refresh network list) top left in this window first, to obtain the most recent listing. Select the name (also referred to as SSID) "Sweex MO251V2" by clicking it once. If it has successfully connected to the wireless network, the notification "Connected" (Connected) appears after a couple of seconds. If you receive a notification saying the wireless connection cannot be configured because it is managed by another programme, disable that software and start again. Once secured, the network will show as "Sweex MO251V2" with a message below detailing "Security-enabled wireless network" (Security-enabled wireless network). When connecting to this secured network you will be prompted for the "Network key" (Network key). If the network key you have entered is incorrect, a notification saying "Limited or no network connection" appears after a couple of seconds. If you change something in the wireless settings of the modem causing you to lose the wireless connection, then complete these steps again. Modem access (Login) Open your web browser. In this example we use `Internet Explorer'. The standard modem IP address is: 192. 168. 251. 1. An IP address is a unique number required by each network device, including a computer or modem, in order to be active within that network. Without an IP address you are unable to make connections within a network. You can now access the modem. 11 English version The modem login screen appears. The standard login is "sweex" and the corresponding password is "mysweex". If this login screen fails to appear, recheck the settings of your Internet browser as described above. In this IP address, only the digits after the last dot may deviate from the IP address of the modem (e. g. : 192. 168. 251. xxx). Do this as follows: Win2000/WinXP: Click "Start" (Start) ­ "Run" (Run)­ Type cmd ­ press ENTER­ In the black window type ipconfig ­ press ENTER and your IP address is displayed. Win98/Me: Click "Start" (Start) ­ "Run" (Run) ­ Type winipcfg ­ press ENTER. Once logged in, the main screen of the modem appears. This screen displays the current Internet connection and a variety of system information. 12 English version Setting the Internet Provider (ISP) In order to facilitate the installation process, the Sweex ADSL 2/2+ Modem/Router Annex A disposes of a pre-programmed list of provider settings. [. . . ] The bar will have filled up and the connection between the computer and the modem will be momentarily interrupted. Subsequently, log into the modem to check the new "Firmware Version" in the "Home" window. Resetting the Modem to its factory settings The Sweex ADSL 2 Modem can be reset to its factory settings in two different ways. After this, all settings which apply to your connection and network need to be reconfigured. During start-up, the factory settings are reloaded and the computer will lose connection with the modem for around 30 seconds. [. . . ]