User manual SUZUKI GRAND VITARA JB420 SUPLEMENTARY SERVICE MANUAL

DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!

If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Diplodocs provides you a fast and easy access to the user manual SUZUKI GRAND VITARA JB420. We hope that this SUZUKI GRAND VITARA JB420 user guide will be useful to you.


SUZUKI GRAND VITARA JB420 SUPLEMENTARY SERVICE MANUAL: Download the complete user guide (15934 Ko)

Manual abstract: user guide SUZUKI GRAND VITARA JB420SUPLEMENTARY SERVICE MANUAL

Detailed instructions for use are in the User's Guide.

[. . . ] IMPORTANT WARNING/CAUTION/NOTE Please read this manual and follow its instructions carefully. To emphasize special information, the words ! WARNING , ! CAUTION and NOTE have special meanings. Pay special attention to the messages high- lighted by these signal words. ! WARNING Indicates a potential hazard that could result in death or injury. ! CAUTION Indicates a potential hazard that could result in vehicle damage. NOTE: Indicates special information to make maintenance easier or instructions clearer. ! WARNING This service manual is intended for authorized Suzuki dealers and qualified service technicians only. [. . . ] DTC Troubleshooting Step Action Yes 1 Was "ABS Check" performed?2 1) Disconnect ABS (ESP®) hydraulic unit / control module Go to Step 5. 2) Check for proper connection to ABS (ESP®) control module connector at terminals "E03-14", "E03-13" and "E03-26" (or "E53-1", "E53-16" and "E53-47"). 3) If OK, then turn ignition switch to ON position and measure voltage between terminals "E03-14" and "E0313", "E03-26" (or "E53-1" and "E53-16", "E53-47"). 2) Check for proper connection to ABS (ESP®) control module connector at terminals "E03-13" and "E03-26" (or "E53-16" and "E53-47"). 3) If OK then turn ignition switch to ON and measure resistance between each terminal of "E03-13", "E03-26" (or "E53-16", "E53-47") and vehicle body ground. 1) Measure voltage between positive battery terminal and vehicle body ground with engine running. Imperfect short between Check charging system "WHT/RED" wire circuit referring to "Generator Test (Undercharged and body ground. Check charging system 1) Measure voltage between terminals "E03-14" and "E03- Poor connection of 13", "E03-26" (or "E53-1" and "E53-16", "E53-47") with "E03-14", "E03-13" and/ referring to "Generator engine running. or "E03-26" (or "E53-1", Test (Overcharged "E53-16" and/or "E53- Battery Check): in Are voltage 18 ± 1. 0 V or less?terminals are in good condition, substitute a known-good ABS (ESP®) hydraulic unit / control module and recheck. Go to Step 3. 5 ABS: 4E-26 DTC C1061: Pump Motor and/or Motor Driver Circuit Wiring Diagram [A] 5 12V 2 WHT/BLU E53-32 3 12V WHT/BLU E03-1 3 12V [B] 6 12V S5JB0E4504017 4 1 BLK BLK E53-16 E53-47 M BLK BLK E03-13 E03-26 M 4 [C] 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 E53 1 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 [D] E03 14 15 16 17 18 19 20 21 22 23 24 25 1 2 3 4 5 6 7 8 9 10 11 12 26 13 I6JB01450010-01 [A]: With ESP® [B]: Without ESP® [C]: ESP® control module connector (viewed from terminal side) [D]: ABS control module connector (viewed from terminal side) 1. ABS hydraulic unit / control module assembly DTC Detecting Condition The ABS (ESP®) control module monitors the voltage at monitor terminal of pump motor circuit constantly with the ignition switch turned ON. It sets this DTC when the voltage at the monitor terminal does not become high / low according to ON/OFF commands to the motor driver (transistor) of the module (does not follow these commands). DTC Troubleshooting Step Action 1 Was "ABS Check" performed?3) Check for proper connection to ABS (ESP®) control module connector at terminal "E03-1" (or "E53-32"). 4) If OK, then measure voltage between terminal "E03-1" (or "E53-32") of module connector and body ground. Measure resistance between terminal "E03-13" and "E03Substitute a known26" (or "E53-16" and "E53-47") of ABS (ESP®) hydraulic unit good ABS (ESP®) / control module connector and vehicle body ground. hydraulic unit / control module assembly and Is resistance less than 1 ?Ground circuit for ABS (ESP®) control module open or high resistance. "WHT/BLU" circuit open. 4E-27 ABS: DTC C1063: Solenoid Valve Power Supply Driver Circuit Failure Wiring Diagram [A] 3 WHT/GRN 2 BLK/YEL 4 GRN/ORN WHT/RED E53-35 E53-1 12V 7 5V 8 9 7 5V 8 12V GRN/ORN WHT/RED E03-7 E03-14 5 [B] 12V 6 S5JB0E4504018 12V 1 9 [C] 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 E53 1 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 [D] E03 14 15 16 17 18 19 20 21 22 23 24 25 1 2 3 4 5 6 7 8 9 10 11 12 26 13 I6JB01450011-02 [A]: With ESP® [B]: Without ESP® [C]: ESP® control module connector (viewed from terminal side) [D]: ABS control module connector (viewed from terminal side) 1. To solenoid valve DTC Detecting Condition ABS (ESP®) control module monitors the voltage at the terminal of solenoid circuit constantly with ignition switch turned ON. [. . . ] CAN communication circuit check 1) Disconnect connectors of all control modules communicating by means of CAN. 2) Check CAN communication circuit between control modules other than Step 4 for open, short and high resistance. DTC check of ECM 1) Connect connectors of disconnected control modules communicating by means of CAN. Go to Step 3. Go to Step 4. Go to Step 5. Repair circuit. 10E-14 Keyless Start System: Step Action 7 DTC check of keyless start control module Yes Using same method, disconnect connectors 1) Turn ignition switch to OFF position. [. . . ]

DISCLAIMER TO DOWNLOAD THE USER GUIDE SUZUKI GRAND VITARA JB420




Click on "Download the user Manual" at the end of this Contract if you accept its terms, the downloading of the manual SUZUKI GRAND VITARA JB420 will begin.

 

Copyright © 2015 - manualRetreiver - All Rights Reserved.
Designated trademarks and brands are the property of their respective owners.