User manual SUPERMICRO X9DBL-IF

[. . . ] X9DBL-i X9DBL-3 X9DBL-iF X9DBL-3F USER’S MANUAL Revision 1. 0c X9DBL-i/3/iF/3F Motherboard User’s Manual The information in this User’s Manual has been carefully reviewed and is believed to be accurate. The vendor assumes no responsibility for any inaccuracies that may be contained in this document, and makes no commitment to update or to keep current the information in this manual, or to notify any person or organization of the updates. Please Note: For the most up-to-date version of this manual, please see our Website at www. supermicro. com. ("Supermicro") reserves the right to make changes to the product described in this manual at any time and without notice. [. . . ] The amber LED on the right indicates activity, while the green LED on the left indicates the speed of the connection. See the tables at right for more information. Link LED IPMI LAN Activity LED IPMI LAN Link LED (Left) & Activity LED (Right) Color/State Link (Left) Activity (Right) Green: Solid Amber: Blinking Definition 100 Mbps Active A VGA LED3 JPL1 JPL2 LAN2 LAN1 IPMI_LAN KB/MOUSE LED1 COM1 USB0/1 FAN5 FAN4 LAN CTRL BMC CTRL JUIDB1 LAN CTRL P2-DIMM1D P2-DIMM1E P2-DIMM1F COM2 TPM/Port80 SLOT1 PCI 33MHZ USB6 USB4/5 USB2/3 S-SATA/ SAS0 S-SATA/ SAS1 S-SATA/ SAS2 S-SATA/ SAS3 S-SATA/ SAS4 JPME2 7 JPME1 JL1 FANA JWD1 T-SGPIO1 T-SGPIO2 SCUSGPIO1 SCUSGPIO2 JBR1 1 S-SATA/ SAS5 S-SATA/SAS6 JBT1 S-SATA/ SAS7 I-SATA5 I-SATA4 I-SATA3 I-SATA2 I-SATA1 I-SATA0 BT1 BIOS JOH1 JWP1 LED2 JF1(FP Control) JD1 Battery JPW3 Intel PCH JIPMB1 CPU1 SLOT2 PCI-E 3. 0 X4(IN X8) CPLD JSTBY1 JI2C2 JI2C1 J9 A. 1. 01 CPU2 SLOT3 PCI-E 3. 0 X8 JPB1 JPG1 CPU2 SLOT4 PCI-E 3. 0 X8 CPU2 SLOT5 PCI-E 3. 0 X8 X9DBL-i/3 (F) JVRM_I2C2 JVRM_I2C1 JCPUVRD_SMB B. IPMI LAN LEDs JPW2 B SP1 CPU1 SLOT6 PCI-E 3. 0 X16 JPW1 P1-DIMM1C P1-DIMM1B P1-DIMM1A CPU2 CPU1 B A FAN3 FAN2 JPI2C1 2-37 FAN1 X9DBL-i/3/iF/3F Motherboard User’s Manual Onboard Power LED An Onboard Power LED is located at LED2 on the motherboard. Be sure to turn off the system and unplug the power cord before removing or installing components. See the tables at right for more information. Onboard PWR LED Indicator (LE1) LED Settings LED Color Off Green Green: Flashing Quickly Green: Flashing Slowly Status System Off (PWR cable not connected) System On ACPI S1 State ACPI S3 (STR) State Rear UID LED The rear UID LED is located at LED3 on the rear of the motherboard. This LED is used in conjunction with the rear UID switch to provide easy identification of a system that might be in need of service. Refer to UID Switch on Page 3-15 for more information. UID LED Status Color/State OS Status Blue: On Blue: Blinking Windows OS Linux OS Unit Identified Unit Identified B LED3 LED1 FAN5 FAN4 LAN CTRL BMC CTRL JUIDB1 LAN CTRL P2-DIMM1D P2-DIMM1E P2-DIMM1F VGA COM1 USB0/1 A. Rear UID LED COM2 TPM/Port80 SLOT1 PCI 33MHZ USB6 USB4/5 USB2/3 S-SATA/ SAS0 S-SATA/ SAS1 S-SATA/ SAS2 S-SATA/ SAS3 S-SATA/ SAS4 JPME2 7 JPME1 JL1 FANA JWD1 T-SGPIO1 T-SGPIO2 SCUSGPIO1 SCUSGPIO2 JBR1 1 S-SATA/ SAS5 S-SATA/SAS6 JBT1 S-SATA/ SAS7 I-SATA5 I-SATA4 I-SATA3 I-SATA2 I-SATA1 I-SATA0 JIPMB1 CPU1 SLOT2 PCI-E 3. 0 X4(IN X8) JSTBY1 JI2C2 JI2C1 J9 BIOS Rev. 1. 01 CPU2 SLOT3 PCI-E 3. 0 X8 JPB1 JPG1 CPLD Intel PCH JOH1 JWP1 CPU2 SLOT4 PCI-E 3. 0 X8 CPU2 SLOT5 PCI-E 3. 0 X8 BT1 Battery X9DBL-i/3 (F) JVRM_I2C2 JVRM_I2C1 JCPUVRD_SMB JPW2 CPU1 SLOT6 PCI-E 3. 0 X16 JPW1 P1-DIMM1C P1-DIMM1B P1-DIMM1A CPU2 CPU1 JPW3 A LED2 JF1(FP Control) SP1 JD1 FAN3 FAN2 JPI2C1 FAN1 2-38 Chapter 2: Installation BMC Heartbeat LED A BMC Heartbeat LED is located at LED1 on the motherboard. See the table at right for more information. BMC Heartbeat LED Status Color/State Green: Blinking Definition BMC: Normal VGA LED3 COM1 USB0/1 A. BMC HeaerKB/MOUSE A BMC CTRL LAN CTRL JUIDB1 LAN CTRL P2-DIMM1D P2-DIMM1E JPL1 JPL2 LAN2 LAN1 IPMI_LAN LED1 FAN5 P2-DIMM1F beat LED FAN4 COM2 TPM/Port80 SLOT1 PCI 33MHZ USB6 USB4/5 USB2/3 S-SATA/ SAS0 S-SATA/ SAS1 S-SATA/ SAS2 S-SATA/ SAS3 S-SATA/ SAS4 JPME2 7 JPME1 JL1 FANA JWD1 T-SGPIO1 T-SGPIO2 SCUSGPIO1 SCUSGPIO2 JBR1 1 S-SATA/ SAS5 S-SATA/SAS6 JBT1 S-SATA/ SAS7 I-SATA5 I-SATA4 I-SATA3 I-SATA2 I-SATA1 I-SATA0 JIPMB1 CPU1 SLOT2 PCI-E 3. 0 X4(IN X8) JSTBY1 JI2C2 JI2C1 J9 BIOS Rev. 1. 01 CPU2 SLOT3 PCI-E 3. 0 X8 JPB1 JPG1 CPLD Intel PCH JOH1 JWP1 CPU2 SLOT4 PCI-E 3. 0 X8 LED2 JF1(FP Control) JD1 CPU2 SLOT5 PCI-E 3. 0 X8 BT1 Battery X9DBL-i/3 (F) JVRM_I2C2 JVRM_I2C1 JCPUVRD_SMB JPW2 SP1 CPU1 SLOT6 PCI-E 3. 0 X16 JPW1 P1-DIMM1C P1-DIMM1B P1-DIMM1A CPU2 CPU1 JPW3 FAN3 FAN2 JPI2C1 FAN1 2-39 X9DBL-i/3/iF/3F Motherboard User’s Manual 2-10 Serial ATA Connections Serial ATA Ports There are six Serial ATA Ports (I-SATA0~ISATA 5) located on the motherboard, including four SATA2 ports and two SATA3 ports. These ports provide serial-link signal connections, which are faster than the connections of Parallel ATA. SCU-SATA/SAS Ports Four Serial_LInk ports (SCU-SATA/SAS 0~3) from Intel SCU are located on the motherboard. Additionally, another four Serial_ Link ports (SCU-SATA/SAS 4~7) are located on the X9DBL-3/3F. See the table on the right for pin definitions. SATA/SAS Pin Definitions Pin# 1 2 3 4 5 6 7 Definition Ground TX_P TX_N Ground RX_N RX_P Ground Note: For more information on SATA HostRAID configuration, please refer to the Intel SATA HostRAID User's Guide posted on our Website @ http:// www. supermicro. com. VGA LED3 JPL1 JPL2 LAN2 LAN1 IPMI_LAN KB/MOUSE LED1 COM1 USB0/1 A. SCU-SATA/ SAS 0~3, 4~7 (S-SATA/SAS 4~7 are for X9DBL-3/3F only) JPW1 JPW2 FAN5 FAN4 LAN CTRL BMC CTRL JUIDB1 LAN CTRL P2-DIMM1D P2-DIMM1E P2-DIMM1F COM2 TPM/Port80 SLOT1 PCI 33MHZ USB6 USB4/5 USB2/3 S-SATA/ SAS0 S-SATA/ SAS1 S-SATA/ SAS2 S-SATA/ SAS3 S-SATA/ SAS4 JPME2 7 JPME1 JL1 FANA JWD1 T-SGPIO1 T-SGPIO2 SCUSGPIO1 SCUSGPIO2 JBR1 1 I-SATA5 I-SATA4 I-SATA3 I-SATA2 I-SATA0 S-SATA/ SAS7 I-SATA1 JIPMB1 CPU1 SLOT2 PCI-E 3. 0 X4(IN X8) Rev. 1. 01 CPU2 SLOT3 PCI-E 3. 0 X8 JPB1 JPG1 CPU2 SLOT4 PCI-E 3. 0 X8 CPU2 SLOT5 PCI-E 3. 0 X8 X9DBL-i/3 (F) JVRM_I2C2 JVRM_I2C1 JCPUVRD_SMB CPU1 SLOT6 PCI-E 3. 0 X16 B S-SATA/ SAS5 S-SATA/SAS6 JBT1 Intel PCH A BIOS JOH1 JWP1 LED2 JF1(FP Control) JD1 JSTBY1 JI2C2 JI2C1 J9 P1-DIMM1C P1-DIMM1B P1-DIMM1A CPLD CPU2 CPU1 BT1 Battery JPW3 SP1 FAN3 FAN2 JPI2C1 FAN1 2-40 Chapter 3: Troubleshooting Chapter 3 Troubleshooting 3-1 Troubleshooting Procedures Use the following procedures to troubleshoot your system. If you have followed all of the procedures below and still need assistance, refer to the ‘Technical Support Procedures’ and/or ‘Returning Merchandise for Service’ section(s) in this chapter. Warning: Always disconnect the power cord before adding, changing or installing any hardware components. Before Power On 1. Make sure that there are no short circuits between the motherboard and chassis. [. . . ] These fatal errors are usually communicated through a series of audible beeps. The numbers on the fatal error list correspond to the number of beeps for the corresponding error. A-1 BIOS Error Beep Codes X9 Motherboard BIOS Error Beep Codes Beep Code/LED 1 beep 5 short beeps + 1 long beep 5 beeps Error Message Refresh Memory error No Con-In or No ConOut devices Description Ready to boot No memory detected in the system Con-In includes USB or PS/2 keyboard, PCI or Serial Console Redirection, IPMI KVM or SOL. Con-Out includes Video Controller, PCI or Serial Console Redirection, IPMI SOL. 1 beep per device Refresh 1 beep or each USB device detected X9 IPMI Error Codes 1 Continuous Beep System OH System Overheat A-1 X9DBL-i/3/iF/3F Motherboard User’s Manual Notes A-2 Appendix B: Software Installation Instructions Appendix B Software Installation Instructions B-1 Installing Software Programs The Supermicro ftp site contains drivers and utilities for your system at ftp://ftp. [. . . ]