User manual SUPERMICRO X8DTL-6F

[. . . ] The important note is located on the rear of the cabinet. Laser Safety This unit employs a laser. Only qualified service personnel should remove the cover or attempt to service this unit, due to the possibility of eye injury. CAUTION: USE OF CONTROLS OR ADJUSTMENTS OR PERFORMANCE OF PROCEDURES OTHER THAN THOSE SPECIFIED HEREIN MAY RESULT IN HAZARDOUS RADIATION EXPOSURE. CAUTION: VISIBLE AND INVISIBLE LASER RADIATION WHEN OPEN AND INTERLOCK DEFEATED. [. . . ] (faster than above) VCR Functions DV AB-1234 0:12:34 5 DVC is in slow reverse playback. Please also read the operating instructions of your DVC for more information. Others SP 2:00 7 6 The menu changes according to the mode of DVC. EN 39 E9TK4BD_EN. book Page 40 Wednesday, January 6, 2010 10:05 PM To stop dubbing: DVC to DVD Dubbing Video VR DVD-RW DVD-RW DVD-R DVD+RW DVD+R Before recording from DVC, see page 19 for connection instructions. (See page 71 for DVC to VCR Dubbing. ) 1) Select "Control" using [K \ L], then press [ENTER\OK]. 3) Press [STOP C]. Note · The tape will rewind a few seconds when you press [ENTER\OK] at step 6 so that the dubbing starts exactly where you press [PAUSE F] instead of [STOP C] at step 5. Other DV device such as cable/satellite box or D-VHS recorder cannot be recognised. · If no video signal is detected from the DVC during DVC to DVD dubbing, the recording will be paused and "I" will flash on the TV screen. The recording will resume when the unit detects the video signal again. · When the DVC is in camera mode, refer to "Guide to DV and On-Screen Display" on page 39. · A DV terminal is a terminal that can use the transmission mode conforming to the IEEE 1394 standards called "Fire Wire". It serves as the interface that connects the PC and peripheral device such as "i. LINK" (registered trademark of SONY). DVD to VCR Introduction Connections Basic Setup / TV View Operation Recording 4 Select "DVD A VCR" using [K \ L], then press [ENTER\OK]. Playback General Setting VCR to DVD 4 Select "VCR A DVD" using [K \ L], then press [ENTER\OK]. General Setting Playback Display Video Recording Clock Channel DivX HDMI DVB Setting Reset All Playback Display Video Recording Clock Channel DivX HDMI DVB Setting Reset All Auto Chapter Recording Audio Select (XP) Dubbing Auto Finalise Mode Aspect Ratio (Video mode) VCR Dubbing Mode DVD DVD Make Recording Compatible VCR Bilingual Recording Audio External Input Audio Video Colour System Editing Auto Chapter Recording Audio Select (XP) Dubbing Auto Finalise Mode Aspect Ratio (Video mode) VCR Dubbing Mode DVD DVD Make Recording Compatible VCR Bilingual Recording Audio External Input Audio Video Colour System 5 6 7 8 Press [SETUP] to exit "Setup" menu. Press [PLAY B], and then press [PAUSE F] at the point you want to start recording. (See page 70. ) Rewind or fast forward the tape to the point where you want to start recording. Function Setup 5 6 7 8 9 Press [SETUP] to exit. Press [PLAY B], and then press [PAUSE F] where you want to start recording. (See page 28. ) 9 Press [DUBBING]. DVD to VCR duplication will start. VCR Functions 10 Press [STOP C] to stop the recording. Note · NTSC dubbing is prohibited in this unit. · Dubbing mode is available only if the tape or disc is not copy-protected. · You cannot change the output mode during VCR to DVD or DVD to VCR duplication. · If you want to watch the duplicated material, after the DVD to VCR duplication, press [VCR] first and then press [PLAY B]. · When "DV" is selected as input, DUBBING function cannot be performed. EN Press [DUBBING]. VCR to DVD duplication will start. 10 Press [STOP C] to stop the recording. Note for VCR to DVD duplication: · During duplication, recording will be paused when a signal other than PAL or SECAM is detected. (See "Video Colour System" on page 38 for details. ) Others 41 E9TK4BD_EN. book Page 42 Wednesday, January 6, 2010 10:05 PM Setting a Disc to Protect VR To cancel finalising (DVD-RW disc only): At step 4, press [STOP C]. [. . . ] If this does not solve the problem, use other type of compatible USB device. · Insert a DVD-video with region codes 2 or ALL. · Check the "Parental Lock" setting. (See page 30. ) · Insert a recordable disc, and ensure the disc status satisfies the recording requirements. Recording Error This disc is protected and not recordable. · Insert a ver. [. . . ]