User manual SUPERMICRO X8DT6-F

[. . . ] X8DT6 X8DTE X8DT6-F X8DTE-F USER’S MANUAL Revision 1. 1a The information in this User’s Manual has been carefully reviewed and is believed to be accurate. The vendor assumes no responsibility for any inaccuracies that may be contained in this document, makes no commitment to update or to keep current the information in this manual, or to notify any person or organization of the updates. Please Note: For the most up-to-date version of this manual, please see our website at www. supermicro. com. ("Supermicro") reserves the right to make changes to the product described in this manual at any time and without notice. [. . . ] 2. 01 SLOT6 PCI-E 2. 0 X8 Intel 5520 LAN CTRL BIOS SIO SLOT4 PCI-E 2. 0 X8 JPL2 JBT1 A LED1 Intel ICH10R South Bridge TPM JP7 J5 SAS0~3 SLOT3 PCI-E 2. 0 X4 BMC CTRL Battery LSI 2008 JIBTN1 SAS CTRL SAS4~7 D1 T-SGPIO1 SLOT1 PCI-E X4 JI2C2 JI2C1 JPB JPG1 COM2 USB6/7 USB4/5 USB3 USB2 I-SATA4 I-SATA3 I-SATA1 I-SATA0 JWF1 B JL1 JWD JPS1 2-29 FAN4 JWOL T-SGPIO2 I-SATA5 I-SATA2 FLOPPY SLOT5 PCI-E 2. 0 X8 IOH JF1 X8DT6/X8DT6-F/X8DTE/X8DTE-F User's Manual I2C Bus to PCI-Exp. Slots Jumpers JI2C1 and JI2C2 allow you to connect the System Management Bus (I2C) to PCI-Express slots. See the table on the right for jumper settings. 1-2 2-3 I2C to PCI-Exp Jumper Settings Jumper Setting Definition Enabled Disabled (Default) VGA Enable Jumper JPG1 allows the user to enable the onboard VGA connector. See the table on the right for jumper settings. VGA Enable Jumper Settings Jumper Setting 1-2 2-3 Definition Enabled Disabled (Default) A. JI2C1 KB/MOUSE FAN5 P1-DIMM3A P1-DIMM3B USB 0/1 IPMI LAN FAN6 P1-DIMM2A P1-DIMM2B P1-DIMM1A P1-DIMM1B CPU2 FAN7 CPU1 Fan JPI2C1 JPW1 JPW2 JPW3 FAN1 B. VGA Enable COM1 VGA PHY LE1 LAN1 CP CPU1 P2-DIMM1B P2-DIMM1A LAN2 P2-DIMM2B P2-DIMM2A FAN8/ CPU2 Fan SLOT7 PCI-E 2. 0 X8 P2-DIMM3B P2-DIMM3A JOH1 JD1 FAN3 SP1 LAN CTRL JPL1 FAN2 X8DT6/E Series Rev. 2. 01 SLOT6 PCI-E 2. 0 X8 Intel 5520 LAN CTRL BIOS SIO SLOT4 PCI-E 2. 0 X8 JPL2 JBT1 Intel ICH10R LED1 J5 SAS0~3 SLOT3 PCI-E 2. 0 X4 BMC CTRL Battery South Bridge TPM JP7 LSI 2008 JIBTN1 SAS CTRL SAS4~7 D1 T-SGPIO1 SLOT1 PCI-E X4 JI2C2 JI2C1 COM2 B A JPB JPG1 USB6/7 USB4/5 USB3 USB2 I-SATA4 I-SATA3 I-SATA1 I-SATA0 JWF1 JWD JL1 JPS1 C 2-30 FAN4 JWOL T-SGPIO2 I-SATA5 I-SATA2 FLOPPY SLOT5 PCI-E 2. 0 X8 IOH JF1 Chapter 2: Installation GLAN Enable/Disable Use JPL1/JPL2 to enable or disable the GLAN Ports 1 & 2. 1. 31 or a later vision of the motherboard only. GLAN 1 & 2 Enable Jumper Settings Pin# 1-2 2-3 Definition Enabled (default) Disabled A. LAN 1 Enable KB/MOUSE FAN5 P1-DIMM3A P1-DIMM3B USB 0/1 IPMI LAN FAN6 P1-DIMM2A P1-DIMM2B P1-DIMM1A P1-DIMM1B CPU2 FAN7 CPU1 Fan JPI2C1 JPW1 JPW2 JPW3 FAN1 B. LAN 2 Enable COM1 VGA PHY LE1 LAN1 CP CPU1 P2-DIMM1B P2-DIMM1A LAN2 P2-DIMM2B P2-DIMM2A FAN8/ CPU2 Fan SLOT7 PCI-E 2. 0 X8 P2-DIMM3B P2-DIMM3A JOH1 JD1 FAN3 SP1 SIO FAN2 X8DT6/E Series Rev. 2. 01 LAN CTRL JPL1 A SLOT6 PCI-E 2. 0 X8 Intel 5520 LAN CTRL BIOS SLOT4 PCI-E 2. 0 X8 JPL2 B JBT1 Intel ICH10R South Bridge TPM JP7 LED1 J5 SAS0~3 SLOT3 PCI-E 2. 0 X4 BMC CTRL Battery LSI 2008 JIBTN1 SAS CTRL SAS4~7 D1 T-SGPIO1 SLOT1 PCI-E X4 JI2C2 JI2C1 JPB JPG1 COM2 USB6/7 USB4/5 USB3 USB2 I-SATA4 I-SATA3 I-SATA1 I-SATA0 JWF1 JWD JL1 JPS1 2-31 FAN4 JWOL T-SGPIO2 I-SATA5 I-SATA2 FLOPPY SLOT5 PCI-E 2. 0 X8 IOH JF1 X8DT6/X8DT6-F/X8DTE/X8DTE-F User's Manual 2-8 Onboard LED Indicators Activity LED Link LED GLAN LEDs Two LAN ports (LAN 1/LAN 2) are located on the IO Backplane of the motherboard. The yellow LED indicates activity, while the Link LED may be green, amber or off to indicate the speed of the connections. See the tables at right for more information. Off Green Amber Rear View (when facing the rear side of the chassis) LAN 1/LAN 2 Activity LED (Left) LED State Color Yellow Status Flashing Definition Active LAN 1/LAN 2 Link LED (Right) LED State LED Color Definition No Connection or 10 Mbps 100 Mbps 1 Gbps IPMI Dedicated LAN LEDs (X8DT6-F/ X8DTE-F Only) In addition to LAN 1/LAN 2, an IPMI Dedicated LAN is also located on the IO Backplane of the X8DT6-F/X8DTE-F. The amber LED on the right indicates activity, while the green LED on the left indicates the speed of the connection. See the tables at right for more information. IPMI LAN (F models only) Link LED Activity LED IPMI LAN Link LED (Left) & Activity LED (Right) Color Link (Left) Activity (Right) Status Green: Solid Amber: Blinking Definition 100 Mbps Active A. LAN1/2 LEDs KB/MOUSE FAN5 P1-DIMM3A P1-DIMM3B USB 0/1 IPMI LAN FAN6 JPI2C1 JPW1 JPW2 JPW3 FAN1 B. LAN3/4 LEDs (X8DT6/iLN4) C P1-DIMM2A P1-DIMM2B P1-DIMM1A P1-DIMM1B CPU2 FAN7 CPU1 Fan COM1 B. Dedicated LAN LEDs (X8DT6-F/X8DTE-F) VGA PHY LE1 LAN1 CP CPU1 A B SLOT7 PCI-E 2. 0 X8 P2-DIMM1B P2-DIMM1A P2-DIMM2B P2-DIMM2A FAN2 LAN2 FAN8/ CPU2 Fan P2-DIMM3B P2-DIMM3A X8DT6/E Series Rev. 2. 01 SP1 LAN CTRL JPL1 FAN3 SLOT6 PCI-E 2. 0 X8 Intel 5520 LAN CTRL BIOS SIO SLOT4 PCI-E 2. 0 X8 JPL2 JBT1 Intel ICH10R LED1 J5 SAS0~3 SLOT3 PCI-E 2. 0 X4 BMC CTRL Battery South Bridge TPM JP7 LSI 2008 JIBTN1 SAS CTRL SAS4~7 D1 T-SGPIO1 SLOT1 PCI-E X4 JI2C2 JI2C1 JPB JPG1 COM2 USB6/7 USB4/5 USB3 USB2 I-SATA4 I-SATA3 I-SATA1 I-SATA0 JWF1 JWD JL1 JPS1 2-32 FAN4 JWOL T-SGPIO2 I-SATA5 I-SATA2 FLOPPY SLOT5 PCI-E 2. 0 X8 IOH JOH1 JD1 JF1 Chapter 2: Installation SAS Heartbeat LED Indicator An Onboard SAS LED is located on the motherboard. See the tables at right for more information. Onboard SAS Heartbeat LED (LED1) Settings LED Color LED1 Definition Blinking: SAS: Normal BMC Heartbeat LED A BMC Heartbeat LED is located at D1 on the motherboard. See the tables at right for more information. BMC Heartbeat LED (D1) Settings LED Color D1 Definition Blinking: BMC: Normal KB/MOUSE FAN5 P1-DIMM3A P1-DIMM3B USB 0/1 IPMI LAN FAN6 P1-DIMM2A P1-DIMM2B P1-DIMM1A P1-DIMM1B CPU2 FAN7 CPU1 Fan JPI2C1 JPW1 JPW2 JPW3 A. BMC Heartbeat LED COM1 VGA PHY LE1 LAN1 CP CPU1 P2-DIMM1B P2-DIMM1A LAN2 P2-DIMM2B P2-DIMM2A FAN8/ CPU2 Fan SLOT7 PCI-E 2. 0 X8 P2-DIMM3B P2-DIMM3A JOH1 JD1 FAN3 SP1 LAN CTRL JPL1 FAN2 X8DT6/E Series Rev. [. . . ] Non-fatal errors are those which, in most cases, allow the system to continue the boot-up process. Fatal errors will not allow the system to continue the boot-up procedure. If a fatal error occurs, you should consult with your system manufacturer for possible repairs. A-1 BIOS Error Beep Codes BIOS Error Beep Codes Beep Code 1 beep 5 short beeps + 1 long beep 8 beeps 1 continuous beep (with the front panel OH LED on) Error Message Refresh Memory error Display memory read/write error System Overheat Description Circuits have been reset. (Ready to power up) No memory detected in the system Video adapter missing or with faulty memory 1 continuous beep with the front panel OH LED on A-1 X8DT6/X8DT6-F/X8DTE/X8DTE-F User's Manual Notes A-2 Appendix B: Software Installation Instructions Appendix B Software Installation Instructions B-1 Installing Software Programs After you've installed the Windows Operating System, a screen as shown below will appear. [. . . ]