User manual SUMMIT 2BA-221
DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!
If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Diplodocs provides you a fast and easy access to the user manual SUMMIT 2BA-221. We hope that this SUMMIT 2BA-221 user guide will be useful to you.
Manual abstract: user guide SUMMIT 2BA-221
Detailed instructions for use are in the User's Guide.
[. . . ] Set the input gain controls so that the red LED only lights occasionally. 4
Summit Audio, Inc.
Front Panel
Tube Output Gain Control
This control varies the tube output gain, including the XLR and balanced TRS outputs. Both the Line/Hi Z input and the Mic Preamp gain controls feed this control. [. . . ] Do not block the cooling holes on the top of the 2BA-221 and always allow adequate ventilation when mounting the unit in a rack enclosure.
6
Summit Audio, Inc.
Rear Panel
Rear Panel
MODEL 2BA-221 20W MAX OUTPUTS STACK SUMMIT AUDIO INC. CARMEL, CA USA INPUTS
FUSE
IN
SUMMITAUDIO. COM
OUT
+4 BAL.
-10 BAL.
INSERT
IN
MIC
A. C. Receptacle
The 2BA-221 is factory wired for either 100, 115 or 230 Volts AC. Before connecting AC power make sure the 2BA-221 is wired for the voltage used in your country.
+4 Balanced Output
This is a balanced, low impedance XLR output connection compatible with professional recording and audio equipment.
Note: You can use all inputs and outputs at the same time for versatility.
1/4" TRS Balanced Line Level Output
This is a -10dB, balanced 1/4" output designed to interface with your recording device, compressor or EQ.
XLR Mic Level Input
This is a balanced low level input designed for microphones. The gain of this channel is adjusted using the front panel Mic Gain control and the -20 dB Pad switch.
1/4" Line Level Input
This is a 10K Ohm impedance, balanced line level input controlled by the front panel Line/Hi-Z Input Gain control.
Model 2BA-221 Microphone Preamplifier
7
Rear Panel
2BA-221 Signal Out Signal Return
Insert
The insert jack allows you to insert a processing device, such as a compressor, after the highpass filter and before the vacuum tube stage. Refer to the block diagram on page 14.
Tip To Input of Processor
Ring To Output of Processor
Stacking Output
This is an unbalanced high level output taken just before the vacuum tube input and insert. Connect the Stacking Output to the Stacking Input of another 2BA-221 to add additional input channels. This jack can also be used as an additional output (phase inverted from input).
INSERT CABLE
Signal is sent out on tip of plug and returned via ring of plug.
When using the insert jack, a cable wired like the one shown above should be used.
Stacking Input
This is an unbalanced high level input which sums into the 2BA-221 just before the tube output stage and insert jack.
From Stack Out of another 2BA221
2 Inputs
SUMMIT AUDIO INC. CARMEL, CA USA OUTPUTS INPUTS
2BA-221
MODEL 2BA-221 20W MAX STACK
The diagram at right shows one way to connect two 2BA-221 units to create a 4-input summing device. The Hi-Z input on the front panel could be used instead of the rear panel line-in jack if desired.
FUSE
IN
SUMMITAUDIO. COM
OUT
+4 BAL.
-10 BAL.
INSERT
IN
MIC
2BA-221
MODEL 2BA-221 20W MAX OUTPUTS STACK SUMMIT AUDIO INC. CARMEL, CA USA INPUTS
FUSE
IN
SUMMITAUDIO. COM
OUT
+4 BAL.
-10 BAL.
INSERT
IN
MIC
2 Inputs Output
8
Summit Audio, Inc.
Basic Operation
Basic Operation
Just Plug-in & Go
1.
Plug your favorite microphone into the rear panel Mic Input jack, plug your instrument into the front panel Hi-Z Input, or your line level device such as a CD player into the rear panel Line Input jack. Connect either the rear panel XLR or 1/4" Output to the input of your mixer or recorder. (Both outputs are balanced. ) Adjust the Mic and Line/Hi Z Level Gain control so that the amber LED is lit most of the time and the red LED only lights occasionally. Adjust the front panel Mic Impedance control to match your microphone. 3.
Important: For proper operation of the 2BA-221 (or any vacuum tube device for that matter), allow the unit to warm up with power on for 15 minutes before use.
4. 6.
Important: Do not block the cooling holes and allow adequate ventilation.
Tips
· Use the Line/Hi Z gain control for solid state sound. · Turn the tube output gain fully counter clockwise for full solid state output. · Turn the solid state gain control fully counter-clockwise, then turn up the tube output to about 2 o' clock. [. . . ] In addition to the +4 Main Balanced Output, the Stacking Output and the -10 Main Output can be used to send the signal to the board, your amp or a headphone monitor amp. Turn up the Tube Output control for more tube sound, use the Solid State input gain for a cleaner sound. To distort the 2BA-221, turn the Tube Output up to 2-3 o'clock and adjust the solid state Hi-Z input gain to get a good level. [. . . ]
DISCLAIMER TO DOWNLOAD THE USER GUIDE SUMMIT 2BA-221
Click on "Download the user Manual" at the end of this Contract if you accept its terms, the downloading of the manual SUMMIT 2BA-221 will begin.