User manual SUB-ZERO W362210

[. . . ] With standard elements like heat sentry and dual setting halogen lighting, Wolf elevates the need for ventilation to an enjoyable perk. This 22" (559) deep model is the low-profile version, 36" (914) wide and available in the classic stainless steel finish. While a classic stainless steel rail is standard on (R) models, a platinum or brass rail is available as a sales accessory. [. . . ] Installation of all Pro wall hoods should be 30" (762) to 36" (914) from the bottom of the hood to the countertop. Models W362210I and W362210IR come with a 600 CFM internal blower, all other lowprofile wall hoods are shipped without the blower assembly. Blower options also vary with the volume of air that needs to be moved and the length of the duct run. Refer to the end of this section for Pro ventilation recommendations and blower options. IMPORTANT NOTE: Install this ventilation hood only with a Wolf blower. Pro wall hoods require a separate, grounded 110/120 V AC, 60 Hz power supply. Placement of the electrical supply is not critical, as long as you provide a minimum of 6" (152) of 120 V AC, 60 Hz power cable. Locate electrical within the shaded area shown in the Installation illustration. Note that the location of the electrical supply will differ between vertical and horizontal discharge blowers. In addition, be aware of local codes and ordinances when installing your service. Vertical or horizontal discharge is applicable on the low-profile wall hoods except for Models W362210I and W362210IR with internal blowers have a vertical discharge only. Refer to the installation instructions shipped with each Wolf product for detailed specifications. This information can also be found on our website, wolfappliance. com. Dimensions in parentheses are in millimeters unless otherwise specified. 5 Planning Information Models W362210 I (R) and W362210 (R) Pro Wall Hoods D U C T I N G C O N S I D E R AT I O N S Models W302210I and W362210I come with internal blowers, all other Wolf Pro low-profile wall hoods are shipped without the blower assembly. Refer to the illustration below for ducting options. Pro low-profile wall hoods have an adjustable discharge location that can run vertically or horizontally. Horizontal discharge is applicable on low-profile wall hoods (excluding Models W302210I and W362210I) using a remote blower. [. . . ] Remote blowers can be mounted on the roof or in some cases, on an exterior wall. Refer to the illustrations below for dimensions of Wolf in-line and remote blowers. Ventilation recommendation charts on the following pages provide minimum CFM recommendations according to the cooking appliance and ventilation system used and blower options for each specific ventilation hood or downdraft. 24 3/8" (619) 24 7/8" (632) 11 3/4" (298) 18" 18 1/2" (470) (457) 12" (305) 4 1/2" (114) 8" (203) 211/2" (546) 12 1/4" (311) 22" (559) 18" (457) In-line BLOWER-60IL In-line BLOWER-110IL 18" (457) 20 3/4" 28 1/4" (718) (527) 21" (533) 10" 29 1/2" (749) (254) 10" 29 1/2" (749) (254) 10" (254) Diameter 24 1/2" (622) 10" (254) Diameter 14 3/4" (375) 10" (254) Diameter 29 1/2" (749) 15 1/2" (394) 29 1/2" (749) 14 3/4" (375) 14" (356) 10 1/8" (257) 10 3/8" (264) 4 3/4" 24 3/4" (629) (121) 22" (559) 7 1/4" (184) 25" (635) 7 1/4" (184) Remote BLOWER-60REM and BLOWER-90REM Dimensions may vary by ± 1/8" (3). [. . . ]