User manual SUB-ZERO L282212I

[. . . ] Pro ventilation hood liners are recommended for use with all Wolf cooking appliances. This Pro liner will accommodate a 30" (762) wide decorative hood. Dimensions in parentheses are in millimeters unless otherwise specified. 9/06 1 Planning Information Model L282212 I Pro Hood Liner F E AT U R E S Stainless steel enclosed liner with seamed construction 600 CFM internal blower included Recessed easy-access controls Infinite-speed blower control Heat sentry feature automatically turns unit on when heat is sensed and automatically adjusts blower speed Halogen lighting with two settings Removable, dishwasher-safe, restaurantgrade stainless steel baffle filters Transition with backdraft damper included Two and five year residential warranty ­ exclusions apply; warranty information can be found on our website, wolfappliance. com OVERALL DIMENSIONS 22 3/8" (568) 3" (76) 3" (76) 12" (305) 12" (305) OVERALL HEIGHT 4"(102) 22 1/2" (572) OVERALL DEPTH 28 3/8" (721) OVERALL WIDTH Dimensions may vary by ± 1/8" (3). [. . . ] In addition, be aware of local codes and ordinances when installing your service. A decorative hood can be created out of wood, plaster, tile or metal. The shape of the decorative hood is not critical, the only place where the the liner and outside cover must meet is at the bottom edge of the metal liner. The decorative hood and liner must fit at the bottom edge in both width and depth. The height of the liner does not have to be the same as the height of the decorative hood, and is generally shorter. The top depth of the liner, 12" (305) standard, must be less than the interior depth of the decorative hood. Measure the interior depth of the hood at the top height of the liner to make sure the liner will fit inside of the decorative hood. Always use the interior measurements of the decorative hood and measure in multiple places. Refer to the installation instructions shipped with each Wolf product for detailed specifications. This information can also be found on our website, wolfappliance. com. Dimensions in parentheses are in millimeters unless otherwise specified. 5 Planning Information Model L282212 I Pro Hood Liner D U C T I N G C O N S I D E R AT I O N S Model L282212I comes with an internal blower, all other Wolf Pro hood liners are shipped without the blower assembly. For hood liners, the remote blower can be mounted on the roof or exterior wall. Pro hood liners have a vertical discharge location as shown in the illustration below. IMPORTANT NOTE: Install these hood liners only with a Wolf blower. Refer to the Pro ventilation charts at the end of this section for recommendations and blower options. Ducting considerations for Pro hood liners. DUCTWORK INSTALLATION THROUGH ROOF ROOF CAP OR REMOTE BLOWER ­ TRANSITION FROM 8" (203) TO 10" (254) DUCT REQUIRED FOR REMOTE BLOWER 8" ROUND DUCT (L282212I) 10" ROUND DUCT (ALL OTHER LINERS) TRANSITION 17 3/4"W x 4 1/4"D TO 8" ROUND 9 3/8"H (L282212I) 22 1/4"W x 9"D TO 10" ROUND 10"H (ALL OTHER LINERS) DIMENSIONS INCLUDE FLANGES VERTICAL DISCHARGE SOFIT OR CABINET OR DUCT COVER DECORATIVE HOOD 12" (305) HEIGHT OF LINER HOOD LINER 221/2" (572) DEPTH OF LINER 30" TO 36" (762­914) COUNTERTOP TO BOTTOM OF DECORATIVE HOOD 36" (914) STANDARD FLOOR TO COUNTERTOP HEIGHT VERTICAL DISCHARGE ONLY FOR VENTILATION HOOD LINERS. Dimensions in parentheses are in millimeters unless otherwise specified. 6 Planning Information Wolf Ventilation Recommendations WOLF BLOWER ASSEMBLIES A ventilation system must include a blower assembly. With a few exceptions where internal blowers are included, Wolf ventilation hoods and downdrafts are shipped without the blower assembly. An internal, in-line or remote blower assembly must be selected to accommodate the cooking appliance, CFM requirements and homeowner preferences. [. . . ] Dimensions in parentheses are in millimeters unless otherwise specified. Remote BLOWER-120REM Remote BLOWER-150REM 7 Planning Information Wolf Ventilation Recommendations P R O V E N T I L AT I O N C F M R E C O M M E N DAT I O N S Pro Hood Liners L282212I DF304 / R304 / SRT304 DF366 / R366 / SRT366 / RT366 DF364 / R364 / SRT364 / RT364 RT362 R488 / RT488 DF486 / R486 / SRT486 / RT486 DF484 / R484 / SRT484 / RT484 R482 / RT482 DF606 / R606 DF604 / R604 600 900 900 900 900 900 900 1100 1100 900 900 1100 1100 900 900 1500 1500 L342212 L402212 L462212 L522212 L582212 Model numbers for dual fuel ranges, gas ranges, sealed burner rangetops and gas rangetops indicate width and number of surface burners. Additional CFM may be required for long duct runs. P R O V E N T I L AT I O N B L O W E R O P T I O N S Pro Hood Liners Blower Description 600 CFM Internal* 1200 CFM Internal 1100 CFM In-Line 900 CFM Remote 1200 CFM Remote 1500 CFM Remote Blower Number Included with (I) Model LBLOWER-120INT (805087) BLOWER-110IL (808332) BLOWER-90REM (801641) BLOWER-120REM (801642) BLOWER-150REM (804701) Hood Liner Models L282212I All Hood Liners (except L282212I) All Hood Liners (except L282212I) All Hood Liners (except L282212I) All Hood Liners (except L282212I) All Hood Liners (except L282212I) *Vertical discharge with 8" (203) round duct. Remote blowers are adjustable discharge with 10" (254) round duct. [. . . ]