User manual SUB-ZERO ISLANDHOOD INSTALL GUIDE

[. . . ] Record the model and serial numbers before installing the Pro island ventilation hood. Both numbers are listed on the rating plate, located on the left wall of the hood shell. L I S T O F M AT E R I A L S The following is a list of materials shipped with the Wolf Pro island ventilation hood. Island Hood Stainless steel island hood Transition with backdraft damper (attached inside hood--needs to be removed) Decorative stainless steel rails and installation components--(R) model hoods only Two control knobs Filters and grease cups (installed in hood) (8­16) #10 x 2" (51) self-tapping hex head screws (number of screws varies with the width of the island hood) (4) 1/4" x 3" (76) lag screws Installation package (taped to filters) Installation Instructions Use & Care Information and product registration card Wolf logo nameplate Serial Number Island Hood (R) Rail Option Model Number Location of rating plate inside left wall Rating plate location Dimensions in parentheses are in millimeters unless otherwise specified. 3 W O L F P R O I S L A N D V E N T I L AT I O N H O O D S I N S TA L L AT I O N C O N S I D E R A T I O N S IMPORTANT NOTE: Wolf Pro island ventilation hoods are recommended for use with all Wolf cooking appliances. Product failure due to improper installation is not covered under the Wolf Warranty. Refer to the Wolf Pro Ventilation Hoods Use & Care Information for warranty details, or visit the Contact / Help section of our website, wolfappliance. com. [. . . ] The transition is shipped upside down in the top of the hood and must be removed and reinstalled in the proper position. Separate the transition from the hood assembly by removing the four shipping screws. Invert and reattach the transition to the hood with the shipping screws. If you are installing a remote blower, drill a 7/8" (22) hole through the hood framing for the conduit. Refer to the remote blower information on page 14 and follow installation instructions provided with the blower. IMPORTANT NOTE: Do not run wiring for the remote blower through the ductwork. Center Filter Bank Location of Screws for Center Filter Bank Filter Remove filters and center filter bank Dimensions in parentheses are in millimeters unless otherwise specified. 9 W O L F P R O I S L A N D V E N T I L AT I O N H O O D S I N S TA L L T H E I S L A N D H O O D IMPORTANT NOTE: If an optional duct cover is to be used, it must be installed before installing the island hood. ACCESSORIES Optional accessories are available through your Wolf dealer. To obtain local dealer information, visit the Locator section of our website, wolfappliance. com. Mark the center location of the hood. If you are installing an internal blower, do not reinstall the center filter bank and filters until the blower installation is complete. Refer to the internal blower information on page 13 and follow installation instructions provided with the blower. 1/4" x 3" (76) Lag Screw #10 x 2" (51) Hex Head Screw Island Hood Top Plate Island hood installation Dimensions in parentheses are in millimeters unless otherwise specified. 11 W O L F P R O I S L A N D V E N T I L AT I O N H O O D S I N S TA L L W I R I N G I M P O R TA N T N OT E You must follow all National Electrical Code regulations. In addition, be aware of local codes and ordinances when installing your service. This ventilation hood must be properly grounded. This unit should be installed by a qualified electrician in accordance with all applicable national and local electrical codes. Run a 120 V AC, 15 amp circuit power cable from the service panel to the electrical box at the center of hood. Refer to the illustration and chart below for the wiring location of your specific model. Insert the conduit through the hole on top of the hood to the electrical box located in center of hood shell. Connect black wire to power supply black wire, white wire to power supply white wire and green wire to green wire or bare wire. Place all wiring connections inside the electrical box and reinstall the cover. Make sure that the wires are secure and that no wires are pinched between the cover and box. Refer to the wiring diagram packaged with the island hood for more information. Before servicing or cleaning unit, switch power off at service panel and lock the service disconnecting means to prevent power from being switched on accidentally. When the service disconnecting means cannot be locked, securely fasten a prominent warning device, such as a tag, to the service panel. Do not remove the control knob bezel to access hood wiring, this will damage the bezel assembly. Location of Knockout for Wiring Model (A) (B) Transition Cut-Out 8" (203) x 5 7/8" (149) Location of Knockout I363418 I423418 I543418 I663418 1" (25) 2" (51) 8" (203) 14" (356) 1" (25) 1 1/2" (38) 1 1/2" (38) 1 1/2" (38) Letters correspond to the illustration. B A Island hood wiring location 12 I N S TA L L AT I O N I N S T R U C T I O N S INTERNAL B L OW E R IMPORTANT NOTE: Refer to the installation instructions provided with the internal blower for additional mounting and wiring instructions. IMPORTANT NOTE: Use wire connectors or wire nuts approved by UL or C/UL. I B L O W E R - 1 2 0 I N T I N S TA L L AT I O N Remove filters and center filter bank from the island hood. Engage the two tabs on the blower into the two slots in the top of the island hood. Secure the blower to the threaded studs with two hex nuts (included with the blower). Plug the blower power cords into receptacles located near the center of the hood shell. [. . . ] Wolf is not responsible for service required to correct a faulty installation. ACCESSORIES Optional accessories are available through your Wolf dealer. To obtain local dealer information, visit the Locator section of our website, wolfappliance. com. Dimensions in parentheses are in millimeters unless otherwise specified. 17 W O L F P R O I S L A N D V E N T I L AT I O N H O O D S I F Y O U N E E D S E RV I C E Maintain the quality built into your Pro island ventilation hood by calling a Wolf authorized service center. For the name and number of the Wolf authorized service center nearest you, check the Locator section of our website, wolfappliance. com, or call Wolf Customer Service at 800-332-9513. When calling for service, you will need the model and serial number of your ventilation hood. [. . . ]