User manual SUB-ZERO INDUCTIONUC GUIDE

[. . . ] Never let loose clothing or other flammable materials come in contact with the cooking surface while in operation. Wet or damp pot holders on hot cooking surfaces may result in burns from steam. Select cookware of the proper size, material and construction for the particular type of cooking being done. This unit is equipped with one or more surface units of different sizes. [. . . ] Power from the front element will automatically be diverted to the rear element, and the total output of the front element on HIGH power will be reduced. This reduction in power will be displayed in the control panel. Hi-Power touch pad H HIG T MEL ON OFF OWER HI-P H HIG OFF SIM ON O H HIG OFF T MEL ON OFF OWER HI-P H HIG OFF SIM ON O OFF Lock "key" touch pad Lock mode "key" touch pad Hi-Power mode touch pad 8 W O L F I N D U C T I O N C O O K TO P U S E & C A R E R E S I D UA L H E AT I N D I C AT O R S I N I T I A L S TA RT- U P As an additional safety precaution, residual heat indicator lights will illuminate when the surface temperature of the glass is above 150°F (65°C). Each heating element has an independently controlled light located to the right of the element as shown in the illustration. Even if the cooktop controls are turned off, you are alerted to any area of the cooktop that remains hot. Before operating the cooktop, please read the entire Use & Care Information. Clean the cooktop surface as outlined in the Ceramic Glass Top Cleaning section on page 12. The cooktop surface must be free of any foreign substance, especially those that could melt and permanently adhere to the glass. During the first uses of your new induction cooktop, you may smell a slight burning odor or see light smoke. IMPORTANT NOTE: When the cooktop is powered up for the first time, the unit will default to Lock mode. To unlock the control panel, refer to the Lock Mode section on page 8. Do not set griddles or oversized pans on residual heat indicator lights. Make sure that the cooktop surface is clean and dry before operating. Do not place hot cooking utensils directly over control panel. Location of indicators H HIG T MEL ON OFF OWER HI-P H HIG OFF SIM ON O OFF Residual heat indicators 9 W O L F I N D U C T I O N C O O K TO P U S E & C A R E C O O K TO P O P E R A T I O N To activate a heating element, touch the OFF ON touch pad that corresponds to the element you wish to use. The power bar indicator graph will begin to blink and show a half-power status. To complete the element activation, touch one of the following symbols or touch pads of the element control while the bar graph is still blinking: Touch the "+" or "­" symbol to set power output to 25% and complete the activation. Touch HIGH to set the power output to full power and complete the activation. Touch MELT to set the power output to the lowest power and complete the activation. To change the power level setting--the element is activated and the power bar graph remains steadily lit: Touch "+" to increase the power level by preset one or two bars on the power bar graph. Touch "­" to decrease the power level by preset one or two bars on the power bar graph. IMPORTANT NOTE: If no cookware is placed on a heating element after activating the element, the control will blink for 30 seconds, then the element will automatically shut off. Apply about 1 teaspoon of nonabrasive cleaner such as Elco Cook Top Cleaning Creme, to the surface of the ceramic glass with a lightly dampened clean cloth. Wipe the cooktop surface with a dry cloth to completely eliminate any remaining moisture. Be careful not to wipe or clean any hot areas to avoid personal injury. It will be safe to clean each element area whenever the corresponding residual heat indicator light has gone out. C O O K TO P F R A M E For general cleaning after each use, apply a nonabrasive cleaner to the stainless steel cooktop frame and gently wipe with a clean towel or cloth. Be sure to remove any cleaner residue from the frame and ceramic glass surface before using the cooktop. C E R A M I C G L A S S TO P C A R E Follow these guidelines to avoid injury and prevent permanent damage to the cooktop. Do not use cooktop as a cutting board. Remove any resulting marks immediately using the method mentioned in the cleaning section. [. . . ] The warranty applies only to products installed in any one of the fifty states of the United States, the District of Columbia or the ten provinces of Canada. This warranty does not cover any parts or labor to correct any defect caused by negligence, accident or improper use, maintenance, installation, service or repair. THE REMEDIES DESCRIBED ABOVE FOR EACH WARRANTY ARE THE ONLY ONES THAT WOLF APPLIANCE COMPANY, LLC WILL PROVIDE, EITHER UNDER THIS WARRANTY OR UNDER ANY WARRANTY ARISING BY OPERATION OF LAW. WOLF APPLIANCE COMPANY, LLC WILL NOT BE RESPONSIBLE FOR ANY CONSEQUENTIAL OR INCIDENTAL DAMAGES ARISING FROM THE BREACH OF THIS WARRANTY OR ANY OTHER WARRANTY, WHETHER EXPRESS, IMPLIED OR STATUTORY. [. . . ]