User manual SUB-ZERO 736TC-PS

[. . . ] See Installation Instructions shipped with unit for detailed specifications. Dimensions in parentheses are in millimeters unless otherwise specified. 4 Planning Information Integrated Model 736TC(I) I N S TA L L AT I O N N OT E S Refer to the illustrations and specifications for overall dimensions, finished rough opening dimensions and installation specifics. IMPORTANT NOTE: The depth of Model 736TC (I) is 24" (610) from the front of the unit to its back. Your design may necessitate moving the unit back, or cabinets forward to achieve a flush fit. [. . . ] Regardless of the routing, allow for 27" (686) of excess copper tubing to remain outside the wall or floor for easy connection to the unit, as shown in the installation illustration on page 4. A 115 volt, 6OHz, 15 amp circuit breaker and electrical supply are required. All Integrated models are equipped with a power supply cord with a 3-prong grounding plug, which must be plugged into a mating 3-prong grounding type wall receptacle. The electrical outlet must be placed so the grounding prong is to the right of the thinner blades. Locate electrical within the shaded area shown in the installation illustration on page 4. In addition, be aware of local codes and ordinances when installing your service. The Integrated Refrigeration Installation Instructions packed with the appliance will give you step-by-step procedures for making sure the unit is installed properly. Dimensions in parentheses are in millimeters unless otherwise specified. 5 Planning Information Integrated Model 736TC(I) C A B I N E T RY A P P L I C AT I O N S Integrated refrigeration is compatible with virtually any style and look of cabinetry. Because of the precise application and the look you may want to achieve, there are important questions you need to answer before ordering panels for the doors and/or drawers. As you look at styles of cabinets, keep some important facts in mind: As the reveal between cabinets and the Integrated unit decreases, the potential exists for severe finger pinching or crushing if a hand or fingers are placed in the opening when the door is closing. IMPORTANT NOTE: The depth of each Integrated unit is 24" (610) from the front of the unit to its back. You must allow for the thickness of the panel you are applying when planning for the finished rough opening depth if you want the front panel to be flush with surrounding cabinetry. You may have to move the unit back into drywall or bring the cabinets forward to achieve a flush fit. Weight Limitations ­ The door panel cannot exceed 53 lbs (24 kg) and each drawer panel must not exceed 16 lbs (7 kg). Panel Thickness ­ Door and drawer panels must be a minimum of 5/8" (16) thick. The height of the door panel can grow beyond 45 3/8" (1153) and exceed the 80" (2032) overall height as long as you stay below the recommended door panel weight limit. The toe kick clearance can vary with the height of the lower drawer panel; the maximum panel height is 16 11/16" (424). You must keep a minimum space of 4" (102) clear below the bottom edge of the lower drawer panel so the unit can be properly vented. A reveal of up to 1/4" (6) is possible, but panel dimensions need to be adjusted accordingly. DOOR PANEL A TOP VIEW A (914) 36" A) ALL REVEALS ARE 1/8" (3) B) DRAWER RAILS ARE ATTACHED TO DRAWER FRONTS C) BOTTOM RAIL MUST BE REMOVABLE 35 3/4" (908) PANEL WIDTH *DIMENSIONS MAY VARY 11/2" (38) 47 7/8" (1216) 84" (2624) SHADED AREA INDICATES STATIONARY STYLES AND RAILS (2032) 80"* B A 13 9/16" (345) B A 341/2" (876)* 15 1/16" 11/2" (38) C (383) A 11/2" (38) (914) 36" 4"* 11/2" (38) (102) 4" (102) (610) 24" FRONT VIEW SIDE VIEW Installation of an Integrated 36" (914) wide tall unit within framed cabinetry. Dimensions in parentheses are in millimeters unless otherwise specified. 8 Planning Information Integrated Model 736TC(I) F R A M E L E S S C A B I N E T RY A P P L I C AT I O N S The illustration below shows a hypothetical installation of an Integrated 36" (914) wide tall unit within frameless cabinetry. Review the illustration, giving particular attention to the overall panel specifications. Also refer to the fullscale illustrations at the end of this section for specifics on door openings. A reveal of up to 1/4" (6) is possible, but panel dimensions need to be adjusted accordingly. FRAMELESS CABINETRY 35 3/4"* (908) PANEL WIDTH (610) 24" A 45 3/8" (1153) (2032) 80"* 79 7/8"* (2029) A 13 9/16" (345) A 341/2" (876)* 16 11/16"* (424) 4"* (102) (914) 36" SIDE VIEW TOE KICK FINISHED OPENING A) ALL REVEALS ARE 1/8" (3) *DIMENSIONS MAY VARY Installation of an Integrated 36" (914) wide tall unit within frameless cabinetry. [. . . ] IMPORTANT NOTE: The depth of each Integrated unit is 24" (610) from the front of the unit to its back. Your design may necessitate moving the unit back, or cabinets forward to achieve a flush fit. Refer to the illustration. TO E K I C K A R E A D E TA I L 9 1016 (268) PANEL 1 2 (13) 1611 16 (424) PANEL 11 9 16 (246) 10 (254) OPTIONAL BASE MOLDING MUST BE REMOVABLE 4 (102) (635) TO WALL 25 5 2 8 TO 4 (67) (102) FLOOR Dimensions in parentheses are in millimeters unless otherwise specified. 13 Planning Information Integrated Model 736TC(I) SUB-ZERO DOOR FRAMED CABINETRY IMPORTANT NOTE: The depth of each Integrated unit is 24" (610) from the front of the unit to its back. Your design may necessitate moving the unit back, or cabinets forward to achieve a flush fit. T 24 (610) TO BACK OF UNIT LINE OF INTERFERENCE* 105° maximum door opening ­ 1/4 scale (top view) LINE OF INTERFERENCE* AT MAXIMUM DOOR OPENING 1 (3) MIN. [. . . ]