User manual SUB-ZERO 685-PS

[. . . ] Refer to the Sub-Zero Design Guide pdf file for additional specifications. Dimensions in parentheses are in millimeters unless otherwise specified. 4 Planning Information Built-In Model 685 I N S TA L L AT I O N N OT E S Refer to the illustrations and specifications for overall dimensions, finished rough opening dimensions and installation specifics. Allow the doors to open a minimum of 90° or you'll have problems removing drawers. With the doors opening at 90°, you may have to move drawers slightly to clear the door interior. Refer to the minimum door swing clearances in the specifications chart. [. . . ] Optional extended full-length handles that provide additional finger clearance for raised panels are available through your Sub-Zero dealer. To obtain local dealer information, visit the Locator section of our website, subzero. com. For framed door panel dimensions and dimensions for the optional panel grille for the framed application, refer to specifications on page 7. To install framed panels, refer to the installation instructions shipped with each unit. The thickness of the panel in this area can range from 1/4" (6) to a maximum of 11/8" (29). If the panel is thicker, provisions must be made to rout out a space to accommodate the decorative bezel surrounding the glasswell. If you choose not to use custom wood panels above or below the glasswell for the framed application, a stainless steel insert panel will be provided with the partial framed accessory kit. This accessory kit includes partial framed molding and classic stainless steel inset handle panel to provide a spill-resistant finish above and below the glasswell on the refrigerator door only. With the framed retrofit accessory kit, existing Model 680 door panels can be used on a new Model 685 framed unit. This accessory kit includes framed retrofit moldings and classic stainless steel inset handle panels to accommodate existing Model 680 framed refrigerator and freezer door panels. IMPORTANT NOTE: When using a partial framed or framed retrofit kit, a 1/2" (13) reveal must be maintained on the bezel side of the panel. To obtain local dealer information, visit the Locator section of our website, subzero. com. H W W Partial Framed Door Panels (identical in size) PA R T I A L F R A M E D PA N E L D I M E N S I O N S Partial framed kit WIDTH HEIGHT Refrigerator Door Panel Freezer Door Panel 15 5/8" (397) 15 5/8" (397) 6711/16" (1719) 6711/16" (1719) Framed retrofit kit Dimensions in parentheses are in millimeters unless otherwise specified. 8 Planning Information Built-In Model 685 O V E R L AY PA N E L S O V E R L AY PA N E L S The overlay design allows decorative panels to cover the door trim for a more seamless appearance that blends with the design of the room. To achieve this look, the most common way is to work with three panels--the decorative overlay panel, a . 10" (3) spacer panel and a 1/4" (6) backer panel. Depending on your cabinet manufacturer, this could be one panel routed for different dimensions or more likely, three different panels. Regardless of the physical construction of the panels (routing or three panel assembly), you will need to follow the exact dimensions and panel placement to ensure a proper fit. The top illustration on this page is a cross section view of the three panel assembly showing placement of the door / drawer / grille trim. The bottom illustration shows a rear view of the three panel assembly and critical dimensions, standard for all overlay models. Overlay models will come with no handle hardware, because the beauty of this design is that you can match the surrounding cabinetry hardware. These models will come with an 11" (279) panel grille which will accept decorative panel inserts to match the look of the door panels. For overlay door and grille panel dimensions, refer to specifications on page 10. IMPORTANT NOTE: Keep in mind that the Sub-Zero door panels have the potential for hitting adjacent cabinets and/or countertops when they are opened. You need to be aware of your surrounding cabinetry and space limitations when using the overlay models. [. . . ] Optional stainless steel handles are available in a variety of diameters and lengths in the classic, platinum and carbon stainless steel finishes and polished chrome. To obtain local dealer information, visit the Locator section of our website, subzero. com. Cut-outs for grille and toe kick area HANDLE PROFILE 1" (25) Glasswell Profile 2" (51) Handle Profile Handle and glasswell profile for stainless steel Model 685 Dimensions in parentheses are in millimeters unless otherwise specified. 12 Planning Information Built-In Model 685 H A N D L E P R O F I L E ­ F R A M E D A P P L I C AT I O N OPTIONAL EXTENDED FULL-LENGTH HANDLE 1" (25) 2" (51) 3" (76) STANDARD FULL-LENGTH HANDLE 11/4"(32) PANEL 1"(25) PANEL 3/4"(19) PANEL 1/2"(13) PANEL 1/4"(6) PANEL 1/4"(6) FRAMED PANEL DOOR F U L L - S C A L E T E M P L AT E S HANDLE PROFILE The following full-scale illustrations enable you to understand some of the unique situations you may face as you design the Built-In units into homes. These templates can be easily photocopied or used in your tracings. The full-scale illustration above shows handle placement for the framed application standard full-length handle and the optional extended full-length handle shown in the dashed line. Dimensions in parentheses are in millimeters unless otherwise specified. 13 Planning Information Built-In Model 685 H A N D L E P L A C E M E N T ­ O V E R L AY A P P L I C A T I O N REFRIGERATOR DOOR PROFILE ­ TOP VIEW 2" (51) STAINLESS STEEL HANDLE PROFILE GLASSWELL PROFILE 1" (25) DOOR NOTE: FOR OVERLAY APPLICATIONS, OPTIONAL STAINLESS STEEL HANDLE MUST BE MOUNTED ON PANEL MINIMUM 5/8" (16) THICK. HANDLE PLACEMENT The full-scale illustration above shows proper placement of the stainless steel handle for the Model 685 refrigerator door in an overlay application. Adequate clearance is required under the handle to assure proper access to the glasswell. IMPORTANT NOTE: For overlay applications, the optional stainless steel handle must be mounted on a panel at least 5/8" (16) thick. Dimensions in parentheses are in millimeters unless otherwise specified. 14 Planning Information Built-In Model 685 PA N E L A N D H A N D L E P R O F I L E ­ 1 3 0 ° D O O R O P E N I N G SUB-ZERO UNIT 130° DOOR OPENING WITH 2" (51) FILLER STRIP (TOP VIEW) SUB-ZERO UNIT FILLER STRIP 2" (51) ALLOW FOR FILLER LAP BEHIND FLANGE MAIN FRAME OVERLAY PANEL 3/4" (19) THICK (NOMINAL) DOOR CLOSED HINGE APPROX PROFILE OF STAINLESS STEEL DOOR AND HANDLE PA N 2) (3 STANDARD FRAMED FULL-LENGTH HANDLE EL PA N 5) EL PA N EL 11 /4" PA NE L DOOR OPEN @ 130° EL 1" (2 /4" (1 9) 3) /2" 1 OPTIONAL FRAMED EXTENDED FULL-LENGTH HANDLE *1 /4" (6 The full-scale illustration above shows the panel and handle profile of a 130° door opening with 2" (51) filler strip for framed applications. [. . . ]