User manual SUB-ZERO 601R-PS

[. . . ] To obtain local dealer information, visit the Locator section of our website, subzero. com. Special Note Specifications are subject to change without notice. Dimensions in parentheses are in millimeters unless otherwise specified. 3 Planning Information Built-In Model 601R I N S TA L L AT I O N S P E C I F I C AT I O N S 24" (610) ROUGH OPENING DEPTH TOP VIEW 351/2" (902) ROUGH OPENING WIDTH 723/4" (1848) ROUGH OPENING HEIGHT LOCATE ELECTRICAL WITHIN SHADED AREA 24" (610) 6" (152) 11" (279) E FRONT VIEW DIMENSIONS Finished Rough Opening Width Finished Rough Opening Height Finished Rough Opening Depth Location of Electrical See Installation Instructions shipped with unit for detailed specifications. Refer to the Sub-Zero Design Guide pdf file for additional specifications. 35 1/2" (902) 72 3/4" (1848) 24" (610) Within shaded area Dimensions in parentheses are in millimeters unless otherwise specified. 4 Planning Information Built-In Model 601R I N S TA L L AT I O N N OT E S Refer to the illustrations and specifications for overall dimensions, finished rough opening dimensions and installation specifics. Allow the door to open a minimum of 90° or you'll have problems removing drawers. With the door opening at 90°, you may have to move drawers slightly to clear the door interior. [. . . ] In addition, be aware of local codes and ordinances when installing your service. To prevent the unit from tipping forward and provide a stable installation, the unit must be secured in place with an anti-tip blocking kit. If there is a solid soffit above the unit with clearance between the unit and the soffit of 1" (25) or less, you won't need to block the unit. For installations with clearances of more than 1" (25), you must block the unit with the anti-tip blocking kit (wood block and hardware) provided with each Built-In unit. Refer to the Built-In Installation Instructions packed with the appliance, which provides step-by-step procedures for making sure the unit is installed properly. Dimensions in parentheses are in millimeters unless otherwise specified. 5 Planning Information Built-In Model 601R A D D I N G PA N E L S In your plan for panels, be sure you are working with the Sub-Zero panel design family called for in your design. If you have chosen the stainless steel design, the unit will be shipped complete with wrapped stainless steel doors and handle hardware. If you and your client have ordered a framed or overlay design model, you will be adding panels to give the unit the custom Sub-Zero look. Specifications on the following pages provide installation considerations for framed and overlay door panels. Side panels can be used with the framed, overlay and stainless steel design applications. Refer to specifications on page 10. Dimensions in parentheses are in millimeters unless otherwise specified. 6 Planning Information Built-In Model 601R F R A M E D PA N E L S If the thickness of the custom panels is less than 1/4" (6), they must be backed up with a sheet of shim material to build the total thickness to 1/4" (6). If the panel is thicker than 1/4" (6), an edge must be routed around the panel to ensure a proper fit. Refer to the illustrations on this page. F R A M E D PA N E L S PANELS 1/4" (6) THICK OR LESS Trim reveal 1/4" (6) min IMPORTANT NOTE: Routing, recessing or optional extended handles may be required on raised panels for finger clearance under the handle. IMPORTANT NOTE: The weight of each panel cannot exceed 50 lbs (23 kg). 1/4" (6) Panel Framed door panel 1/4" (6) thick or less The traditional framed models come with an 11" (279) louvered grille and elegant full-length handle. Optional extended full-length handles that provide additional finger clearance for raised panels are available through your Sub-Zero dealer. To obtain local dealer information, visit the Locator section of our website, subzero. com. To install framed panels, refer to the installation instructions shipped with each unit. These instructions can also be found on our website, subzero. com. PANELS THICKER THAN 1/4" (6) Trim reveal 1/4" (6) min Rout to 1/4" (6) thickness F R A M E D PA N E L D I M E N S I O N S WIDTH HEIGHT Door Panel Handle Recess Location Framed door panel thicker than 1/4" (6) 34 1/8" (867) 5815/16" (1497) A ­ 29 15/32" (749) 50 lbs (23 kg) Maximum Panel Weight 14" (356) H A W Framed Door Panel H Dimensions in parentheses are in millimeters unless otherwise specified. 7 Planning Information Built-In Model 601R O V E R L AY PA N E L S O V E R L AY PA N E L S The overlay design allows decorative panels to cover the door trim for a more seamless appearance that blends with the design of the room. To achieve this look, the most common way is to work with three panels--the decorative overlay panel, a . 10" (3) spacer panel and a 1/4" (6) backer panel. Depending on your cabinet manufacturer, this could be one panel routed for different dimensions or more likely, three different panels. Regardless of the physical construction of the panels (routing or three panel assembly), you will need to follow the exact dimensions and panel placement to ensure a proper fit. [. . . ] Optional stainless steel handles are available in a variety of diameters and lengths in the classic, platinum and carbon stainless steel finishes and polished chrome. To obtain local dealer information, visit the Locator section of our website, subzero. com. Cut-outs for grille and toe kick area Dimensions in parentheses are in millimeters unless otherwise specified. 10 Planning Information Built-In Model 601R H A N D L E P R O F I L E ­ F R A M E D A P P L I C AT I O N OPTIONAL EXTENDED FULL-LENGTH HANDLE 1" (25) 2" (51) 3" (76) STANDARD FULL-LENGTH HANDLE 11/4"(32) PANEL 1"(25) PANEL 3/4"(19) PANEL 1/2"(13) PANEL 1/4"(6) PANEL 1/4"(6) FRAMED PANEL DOOR F U L L - S C A L E T E M P L AT E S HANDLE PROFILE The following full-scale illustrations enable you to understand some of the unique situations you may face as you design the Built-In units into homes. These templates can be easily photocopied or used in your tracings. The full-scale illustration above shows handle placement for the framed application standard full-length handle and the optional extended full-length handle shown in the dashed line. Dimensions in parentheses are in millimeters unless otherwise specified. 11 Planning Information Built-In Model 601R H A N D L E P R O F I L E ­ S T A I N L E S S S T E E L / O V E R L AY A P P L I C A T I O N S STANDARD STAINLESS STEEL HANDLE 1" 2" (51) 3" (76) 11/4" (32) PANEL 1" (25) PANEL 3/4" (19) PANEL 5/8" (16) PANEL 1/2" (13) PANEL 1/4" (6) PANEL 1/4" (6) APPROXIMATE THICKNESS OF WRAPPED STAINLESS STEEL DOOR DOOR NOTE: FOR OVERLAY APPLICATIONS, OPTIONAL STAINLESS STEEL HANDLE MUST BE MOUNTED ON PANEL MINIMUM 5/8" (16) THICK. PA N E L A N D H A N D L E P R O F I L E The full-scale illustration above shows handle placement for the standard stainless steel handle on the wrapped stainless steel door and on overlay panel applications shown in the dashed line. IMPORTANT NOTE: For overlay applications, the optional stainless steel handle must be mounted on a panel at least 5/8" (16) thick. For overlay applications, mount door handles close to the opening edge of the door for ease of opening. Dimensions in parentheses are in millimeters unless otherwise specified. 12 Planning Information Built-In Model 601R PA N E L A N D H A N D L E P R O F I L E ­ 1 3 0 ° D O O R O P E N I N G SUB-ZERO UNIT 130° DOOR OPENING WITH 2" (51) FILLER STRIP (TOP VIEW) SUB-ZERO UNIT FILLER STRIP 2" (51) ALLOW FOR FILLER LAP BEHIND FLANGE MAIN FRAME OVERLAY PANEL 3/4" (19) THICK (NOMINAL) DOOR CLOSED HINGE APPROX PROFILE OF STAINLESS STEEL DOOR AND HANDLE PA N 2) (3 STANDARD FRAMED FULL-LENGTH HANDLE EL PA N 5) EL PA N EL 11 /4" PA NE L DOOR OPEN @ 130° EL 1" (2 /4" (1 9) 3) /2" 1 OPTIONAL FRAMED EXTENDED FULL-LENGTH HANDLE *1 /4" (6 The full-scale illustration above shows the panel and handle profile of a 130° door opening with 2" (51) filler strip for framed applications. [. . . ]